![]() |
DCN LAN Switch - Printable Version +- Free Academic Seminars And Projects Reports (https://easyreport.in) +-- Forum: Seminars Topics And Discussions (https://easyreport.in/forumdisplay.php?fid=30) +--- Forum: Miscellaneous Seminars Topics (https://easyreport.in/forumdisplay.php?fid=21) +---- Forum: General Seminar Topics (https://easyreport.in/forumdisplay.php?fid=58) +---- Thread: DCN LAN Switch (/showthread.php?tid=57846) |
DCN LAN Switch - sairadhrub - 10-04-2017 DCN LAN Switch Introduction This Installation and Configuration Instruction describes how to install the DCN LAN Switch (DLS) in a 19 rack and how to set up, configure and maintain the DLS. The DLS is a wide-range powered 8-port Ethernet switch with support for power-over-Ethernet (PoE) on one port. The DLS is intended to be used to connect devices on a local site LAN to the DCN via, for example, the NPU of a MINI-LINK TN node. The DLS can be manually configured in a flexible way to support various Ethernet communication modes. ERICSSON PoE DCN LAN Switch P1 PWR DC 24-48V + - PoE PUSH TO SELECT HOLD TO APPLY Ethernet Ports 10/100 P1 manual P2-4 manual P5-8 manual 100 Mbps Full duplex P1 priority Link P2 P3 P4 P5 P6 P7 P8 9468 Figure 1 DCN LAN Switch 1.1 Target Group This Installation and Configuration Instruction is written for field technicians and supervisors who work with installation, configuration and maintenance of MINI-LINK E and MINI-LINK TN equipment on site. It is assumed that the user: Has basic understanding of MINI-LINK network design, operation and terminology. Is familiar with his or her own MINI-LINK network configuration. Has basic understanding of networking technologies. Has the proper education, training and competence required to perform the tasks in this document correctly. 1531-BFB 109 002/1 Uen A 2007-10-17 1 DCN LAN Switch 1.2 Revision Information This is the first release of the Installation and Configuration Instruction and it applies to: DCN LAN Switch BFB 109 002/1 R1A. 1.3 Related Documents Table 1 on page 2 contains documents related to the installation and configuration of the DLS. References are made in Italics using the document name only. Table 1 Related documents MINI-LINK E ETSI Indoor Installation Manual EN/LZT 712 0176 MINI-LINK E ANSI Indoor Installation Manual AE/LZT 712 0189 MINI-LINK TN, MINI-LINK HC, MINI-LINK E Outdoor Installation Instruction EN/LZT 712 0015 MINI-LINK TN, MINI-LINK HC, MINI-LINK E ETSI Product Catalog EN/LZT 712 0191 MINI-LINK TN, MINI-LINK HC, MINI-LINK E ANSI Product Catalog AE/LZT 712 0195 MINI-LINK DCN Guideline ETSI 1/153 43-FGB 101 004/1 Uen MINI-LINK TN ETSI Operation Manual EN/LZT 712 0177 MINI-LINK TN ANSI Operation Manual EN/LZT 712 0216 2 1531-BFB 109 002/1 Uen A 2007-10-17 Introduction 1.4 Typographic Conventions The following typographic conventions are used: Elements in the user interface such as window names, dialog box titles and options and menu commands are formatted like this: AaBbCc123 Resource identifiers such as file paths, database names and Uniform Resource Locators (URLs) are formatted like this: AaBbCc123 Keywords, functions and anything else that the system provides are formatted like this: AaBbCc123. Variables and other placeholders that the system provides are formatted like this: <AaBbCc123>. Keywords, functions and anything else that have to be entered exactly as shown are formatted like this: AaBbCc123. Variables and other placeholders you have to provide are formatted like this: <AaBbCc123>. 1.5 Copyright for Third Party Software Products Adobe and Acrobat Reader are registered trademarks of Adobe Systems Incorporated in the United States and/or other countries. 1531-BFB 109 002/1 Uen A 2007-10-17 3 DCN LAN Switch 1.6 Technical Support If you have a technical question or have encountered a problem working with MINI-LINK equipment, please contact your local Ericsson representative. When contacting your local Ericsson representative, please provide the following information for the fastest possible service: Product serial number. Your name, company name and phone number. Product name and version number. Type and version of operating system, including service packs. Complete description of the problem, including steps to reproduce it. Exactwordingofany messages displayed when you encountered the problem. Steps taken to resolve the problem. All previous correspondence with Ericsson. 4 1531-BFB 109 002/1 Uen A 2007-10-17 Safety Instructions 2 Safety Instructions 2.1 Introduction This section describes the system used for presenting safety information. Note: Reduce the risk of accidents by studying all the instructions carefully before you start working. Should questions arise regarding the safety instructions, contact your supervisor or your local Ericsson representative. The relevant manual (including this safety information) and specific instructions supplied by Ericsson must be followed in any work performed on Ericsson products or systems. Sufficient knowledge of English or of any other language, in which the manuals or instructions are available, is necessary to perform the tasks in the manual in a correct and safe way. The safety information in the relevant manuals presupposes that any person performing work on Ericsson products or systems has the education, training and competence required to perform the task correctly. For certain tasks additional or special training might be required. For more precise information on the amount and content of the general and/or special training required to work on Ericsson products or systems, please contact the local Ericsson company. Ericsson does not take any responsibility for either personal injury or damage to tangible property that is caused by work performed on Ericsson products and systems in conflict with the safety instructions set out in this manual. 2.2 Standards 2.2.1 Safety Standards for Information Technology Equipment Equipment for the ETSI market meets the requirements according to IEC/EN 60950-1 and IEC/EN 60529. Equipment for the ANSI market meets the requirements according to ANSI/UL 1950 or ANSI/UL 60950 and CAN/CSA-C.22.2 No. 950-95 or CAN/CSA-C22.2 No. 60950. 1531-BFB 109 002/1 Uen A 2007-10-17 5 DCN LAN Switch 2.3 Safety Requirements The safety requirements in the following sections must be followed to avoid personal injury and damage to tangible property. It is the responsibility of the local project manager / supervisor to make certain that local regulations and the safety instructions in this manual are known and followed. 2.3.1 Installation and Maintenance Personnel Installation and maintenance must be carried out by authorized personnel with the appropriate technical training and experience necessary to be cognizant of hazards during installation and maintenance, and of measures to minimize any danger to themselves or any other person. 2.3.2 Access to Equipment The equipment must be installed in a restricted access location and access shall be restricted to authorized personnel. 2.3.3 Safety Regulations Use local safety regulations where these are mandatory. The safety instructions in this manual shall be used as a supplement to the local regulations. In case of conflict between the safety instructions in this manual and the local safety regulations, the local safety regulations shall prevail if these are mandatory. If the local regulations are not mandatory the safety instructions in this manual shall prevail. 2.3.4 Installation Hardware Do not use any installation components (for example screws and nuts) other than what is enclosed with the equipment or recommended by Ericsson. 2.3.5 Installation Procedures and Tools The installation procedures in this manual must be followed. Make sure that: workinginstructions are followed recommended tools are used adequate safety devices are used the risk of falling and falling objects is known As a guide to identifying potentially hazardous installation steps, safety symbols as in Section 2.4 on page 7 are used throughout the manual. 6 1531-BFB 109 002/1 Uen A 2007-10-17 Safety Instructions 2.4 Safety Symbols and Definitions This section shows the method used for presenting safety information. 2.4.1 Danger, Warning and Caution The following three levels, shown in order of urgency, are used. Danger! Danger means that an accident may occur if the safety precautions are neglected. This type of accident is likely to be fatal. Warning! Warning means that an accident may occur if the safety precautions are neglected. This type of accident may be fatal or can cause serious injury. Caution! Caution means that an accident may occur if the safety precautions are neglected. This type of accident may cause minor injury or damage to tangible property. 2.4.2 Notes Note: Notes are used to call to the attention of the reader key points that might otherwise be overlooked. 2.4.3 Electrostatic Discharge Figure 2 ESD symbol 1531-BFB 109 002/1 Uen A 2007-10-17 7 DCN LAN Switch The Electrostatic Discharge (ESD) symbol indicates when external ESD protection must be used to avoid possible damage to the equipment. Electrical charges are generated by friction when a body moves, rubs against clothes, slides against a chair, when shoes rub against the floor, and when you handle ordinary plastics, etc. Such charges may remain for a considerable period of time. Handling of Printed Board Assemblies and IC Components Always use an approved antistatic bracelet to avoid damage to components mounted on printed board assemblies. The ESD wrist strap contains a resistor with an ohmic value greater than 1 M in the cable to protect the operator. The resistance value is low enough to discharge the electrostatic voltage. Never replace the cable with any other cable. The ESD wrist strap must be connected to earth. Storing and Transporting Printed Board Assemblies and IC Components Use the original packaging. If this is not available, use a conductive material, or a special IC carrier that either short-circuits or insulates all leads of the components. |