08-17-2017, 12:05 AM
Remote Control of Digital Factory Through Web This project reports the development of hardware and software for remote control of a digital factory controlled through internet.
Distributed Guarding and Alarming System Based on Telephone Automatically Dialing and Remote Communication Technology Single chip microprocessor A T89C51 processes data signal collection and realize telephone automatically dialing-alarming when there is unusual condition, as well as it controls wireless transceiver chip nRF905 to complete data transmission between monitor controller and work central station controller. Upper PC of manager is connected with work central station controller though USB interface, which realizes distributed safety monitor and guarding-alarming system of intelligent building design.
Research of traffic Signal Light Intelligent Control System based on Microcontroller A Development of Distributed area traffic signal lights control Based on Single-chip Microcontroller through CAN BUS is described.
Development of a Real-time Mine Auxiliary Monitoring System Using RF Wireless Sensor Networks This Paper proposes a mine auxiliary sensor system (MASS) will effectively monitor all situations in mine especially for the safety of mineworkers.
Research on temperature and humidity monitoring under mine based on optical fiber communication system For the Problem of temperature drift, inexact and great transmission loss of the monitoring of environment temperature and humidity under the mine, this paper proposes the temperature and humidity monitoring and optical fiber communication transmission.
Research and Development of a Intelligent Temperature-Measuring System Based on 1-Wire Bus Temperature monitoring method of 1-wire bus was Proposed.
Distributed sensor for steering wheel Grip Force Measurement in Driver Fatigue Detection. This Smart Project uses a Microcontroller and a Grip sensor Connected to it using CAN Protocol for a safe drive in case of any tiredness for the driver.
The Integrated unit for MEMS Based pressure Measurement. This Project involves a MEMS sensor to calculate the pressure and is connected to the microcontroller through ADC using 12C protocol. The Pressure values cam is monitoring in a PC via UART.
Research on Embedded Data display unit Based on CAN Bus This Project uses an ARM Processor and a LCD to display the data which has been sent though the can protocol which would be very efficient system.
Research & Development of the remote I/O Data Acquisition system based on Embedded ARM Platform In this Project the various industrial measurement units can be integrated on to an Ethernet bridge using an ARM processor to send info to a server database using an RTOS.
Microcontroller based standalone PV System for Wireless Sensor Node This Project uses a microcontroller which monitors the power of an active device & enables Switch to change the device only if necessary to improve the life of that device.
CAN Bus-Based Distributed fuel system with smart components In this project a new distributed control system for very high efficient fuel management application is introduced with the help of a CAN enabled microcontroller.
A Low-cost intelligent Gas Sensing Device for military Applications. This project uses sensors connected to a microcontroller implemented using the C Programming language on that to detect the gas and to intimate the military troop regarding the level of the particular detected Gas.
Study on ARM Processor Based Embedded intelligent Yields System Controller This System Proposes as effective scheduling algorithm for the efficiency Improvement of a yielding System using ARM Processor with moisture, pressure sensing units.
A Simple capacitive security card system. This project uses a simple & reliable capacitive security card system Which has been designed and consists of capacitive card reader system, an integrator, rectifying circuit, an 8051 Microcontroller & indicators for very safe security System.
Research & Design of industrial Ethernet Intelligent Gateway Based on ARM This project is going to deploy a system capable of bridging various industrial protocols like CAN,RS232 on to an Ethernet gateway to measure the parameters and communicating with system.
Measuring & transmitting vital body signs using MEMS sensor. The system proposes an innovative patient body movement monitoring & intimation system by the aid of an active MENS sensor. It deals with acceleration of the Patient.s
ASSIST-Automated system for surgical instrument and sponge tracking. The system deploys and operation monitoring system for the usage of surgical tools, sponges and tracking critical missing tools before the event of operation completion for a secure surgery
procedure.
Smart Jacket Design for Neonatal Monitoring with Wearable sensors Smart Jacket proposed in this paper is the vision of a wearable unobtrusive continuous monitoring system realized by body sensor networks (BSN) & wireless Communication.
Design of Medical Infusion Monitor & protection system Based On wireless communication Technology A medical infusion monitor & protection system is designed based on technologies of photoelectric monitor, modulation demodulation, single chip microprocessor (SCM) & wireless communication.
Research on portable Instrument for Determining Hemoglobin Concentration Whole
Blood A Portable hemoglobin concentration determinate has been developed, utilizing the disposable microcuvette containing reagent, which could be used for performing the quick online test of undiluted & unemployed whole blood within 30-60 Seconds.