Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
DESIGN AND FABRICATION OF A TENSION LESS BIKE
#1

Submitted by
P. RATHNA KUMAR
S. JAGADEESH
K. SARAN KUMAR
S. DINESH

[attachment=14464]
ABSTRACT
An automobile is a wheeled motor vehicle used for transporting passengers, which also carries its own engine or motor. But normally two wheelers are used most of the people which is economical. Motorcycles are one of the most affordable forms of motorized transport in many parts of the world and, for most of the world's population; they are also the most common type of motor vehicle. There are around 200 million motorcycles (including mopeds, motor scooters and other powered two and three-wheelers) in use worldwide, or about 33 motorcycles per 1000 people.While people choose to ride motorcycles for various reasons, those reasons are increasingly practical, with riders opting for a powered two-wheeler as a cost-efficient alternative to infrequent and expensive public transport systems, or as a means of avoiding or reducing the effects of urban congestion. In places where it is permitted, lane splitting, also known as filtering, allows motorcycles to use the space between vehicles to move through stationary or slow traffic.In this motorcycle, major accidents occur due to the carelessness. Some of them forgot to take the side stand and they start driving with that side stand. This leads to an accident. Sometimes if we are going to a long drive there is a chance of air leakage in our bikes or our bike may get puncher. In that time there is no puncher shop nearby us. So we get into trouble.
INTRODUCTION
TENSION LESS BIKE

While people choose to ride motorcycles for various reasons, those reasons are increasingly practical, with riders opting for a powered two-wheeler as a cost-efficient alternative to infrequent and expensive public transport systems, or as a means of avoiding or reducing the effects of urban congestion. In places where it is permitted, lane splitting, also known as filtering, allows motorcycles to use the space between vehicles to move through stationary or slow traffic.
In this motorcycle, major accidents occur due to the carelessness. Some of them forgot to take the side stand and they start driving drive there is a chance of air leakage in our bikes. In that time there is no puncher shop with that side stand. This leads to an accident. Sometimes if we are going to a long nearby us. So we get into trouble.
Many engineers found out solutions for reduce the tension of bike. But it will not so much effective than our discovery.
Our aim is to reduce the tension of one who is driving the vehicle. Because some of the carelessness leads to a death. So every time we always aware of that. So our mini project helps a little bit to reduce those kind of incidents. Our objective is to inflate the tyre in some emergency conditions where there is no helping hands.This method is one of the easiest methods and also the cheapest methods
Our mini project consists of two things:
1. Side Stand Indicator Modulation 2. A Compressor Of Less Weight
These two things are most important for all the bikes. All the bike riders knew how important these two things are. We are doing some of the alterations in the bike to make a successful of these two.
SIDE STAND:
The side stand is the one of the most nice founded thing of our senior engineer and attached to bike instead of the centre stand most of the times people use only side stand in their bike because it easy to use compare to centre stand.
Fig. 1
PROBLEM:
Many of the people forget to take the side stand of their bike while taking their bike to drive from parking. Because of this the side stand remains in the same position as how it was in parking.
CAUSE OF NOT TAKING THE SIDE STAND:
Due to this small forgiveness it lead to
1) Leads to accident
2) Leads to death
3) Leads to loose of their any organ of the body
TILL NOW EXISTING SOLUTION:
Many of our senior engineers have thinked over this problem and under gone many ideas and they implemented it and tested. But in that two things came into success. They are
1) In one private company (TVS Scooty Pep) bike they have introduced a system it consist of a beep sound will be heard.
Fig. 2
2) In the other case in another private company (Bajaj Pulsar) bike they have introduced a system i.e. they have kept a sensor (or) indicator near the speedometer which indicates that if it blinks the side stand is put (or) being used if the light does not blinks the side stand has been taken (or) the side stand is not in use.
Reply



Forum Jump:


Users browsing this thread:
1 Guest(s)

Powered By MyBB, © 2002-2024 iAndrew & Melroy van den Berg.