BEHAVIOUR OF REINFORCED CONCRETE BEAMS COCONUT SHELL AS COARSE AGGREGATES. ....etc

[:=Read Full Message Here=:]

Reinforced concrete structures often have to face modification and improvement of their performance during their service life. The main contributing factors are change in their use of ,new design standards, deterioration due to corrosion in the steel caused by exposure to an aggressive environment and accident events such as earthquakes .In such circumstances there are two possible solutions: replacement or retrofitting.
Retrofitting of flexural concrete elements are traditionally ac ....etc

[:=Read Full Message Here=:]

ABSTRACT
This paper presents the results of experimental studies concerning the flexural strengthening of RC beams using externally bonded Slurry Infiltrated Mat CONcrete (SIMCON) laminates. A total of four reinforced concrete beams were cast and tested in the laboratory over an effective span of 3000 mm. Three beams were strengthened with bonded SIMCON laminate at the bottom under virgin condition and tested until failure; the remaining one beam was used as control specimen. Static responses of all the beams we ....etc

[:=Read Full Message Here=:]

to get information about the topic Fatigue Behaviour Of Steel Fibre Reinforced Concrete Beams full report,ppt and related topic refer the page link bellow

http://seminarsprojects.net/Thread-fatigue-behaviour-of-steel-fibre-reinforced-concrete-beams--2202 ....etc

[:=Read Full Message Here=:]

OVERHEAD CAMSHAFT ENGINE
* INTRODUCTION :-
OHV means OverHead Valve
An engine design where the camshaft is installed inside the engine block and valves are operated through lifters, pushrods and rocker arms (an OHV engine also known as Pushrod engine).
Although an OHV design is a bit outdated, it has been successfully used for decades. An OHV engine is very simple, has more compact size and proven to be durable.
* Classification :-
Single OverHead Cam
Double OverHead Cam
Pushrod Engines
* Single OverHea ....etc

[:=Read Full Message Here=:]

Camshaft

Double overhead cams control the opening and closing of the valves
The camshaft is used in IC Engines to operate poppet valves. It consists of a cylindrical rod running the length of the cylinder bank with a number of oblong lobes or cams protruding from it, one for each valve. The cams force the valves open by pressing on the valve, or on some intermediate mechanism, as they rotate.
The relationship between the rotation of the camshaft and the r ....etc

[:=Read Full Message Here=:]

Construction material subjected to repetitive or cyclic loading have to be qualified for their fatigue behaviour. Generally their behaviour is considered satisfactory if they withstand two million cycle of repetitive loading without distress or failure at that required mean stress level and range stress.
The recent research in reinforcing Portland cement based material with randomly distributed fibres was spurred by pioneering research or fibre reinforced concrete (FRC) conducted in the United state in the 1960s.The addition of fibre in the co ....etc

[:=Read Full Message Here=:]

Hello,

Presently I am using forging for manufacturing cam shaft.

The yield I am achieving 60%.To improve the yield to 75 % do you have any alternate process please provide.

Material : Low Carbon Steel.

Application : Used in Fuel Injection Pump operates at 1500 Rpm and Higher load. ....etc

[:=Read Full Message Here=:]

Deep beams are structural members loaded as simple beams in which a significant amount of the load is carried to the supports by a compressive force that combines the charge and the reaction. As a result, the strain distribution is no longer considered linear, and the shear deformations become significant in comparison with pure bending.

Horizontal load-bearing floor slabs, short-section beams carrying heavy loads and transfer beams are examples of deep beams. The deep beam is a beam having a large depth / thickness ratio and a depth ratio o ....etc

[:=Read Full Message Here=:]

toyota altezza 3s ge camshaft timing

The Toyota S Series engines are a family of straight-4 engines with displacement from 1.8 L to 2.2 L produced by Toyota Motor Corporation from January 1980 to August 2007. The series has cast iron engine blocks and alloy cylinder heads.

Toyota 3S-GE engine
From Wikipedia, the free encyclopedia
(Redirected from 3S-GE)
Jump to: navigation, search

The Toyota 3S-GE is an in-line 4 cylinder engine manufactured by Toyota and tuned by Yamaha Motor Company Ltd. Its cylinders are numbered 1-2-3-4 with cylinder num ....etc

[:=Read Full Message Here=:]