Ajaya Kumar Kavala
Research Scholar
Department of Physics
IIT Patna


Introduction of Dielectrics

Dielectric is an entity ,in which equal positive and negative charges separated by equal small distance.
In which each molecule has permanent dipole moment P
This type of materials are known as polar materials
Different molecules has different different directions of the dipole moment.
In Non polar materials ,The centre of the positive charge distributution in an atom or molecules coinci ....etc

[:=Read Full Message Here=:]

H-Shaped Dielectric Resonator Antenna for UWB application



INTRODUCTION
The extremely wide spectrum of 3.1 to 10.6 GHz with 15 bands of bandwidth greater than 500 MHz and power limit less than -41.3 dBm/MHz announced by FCC for Ultra wide band. The release of this Spectrum has rapidly increased the research in UWB technology for communications, radar imaging, and localization applications . Radio systems based on UWB technology offer opportunities for transmission of high data r ....etc

[:=Read Full Message Here=:]

to get information about the topic electric heating resistance heating induction heating dielectric heating arc furnaces principle applicationsrelated topic refer the page link bellow

http://seminarsprojects.net/Thread-electrical-heating-methods ....etc

[:=Read Full Message Here=:]

The High frequency attenuation in shielded distribution cable has been extensively studied. But in the case of solid dielectric cable, this has not been done. A solid dielectric cable has a bit more complex structure including the semiconducting bedding layers and a moisture barrier.high frequency loss is created by these sources.The purpose of these bedding layers is to seal the cable against moisture ingress and also accomodate for the thermal expansion of the cable. The cables studied here are the ones with a corrugated copper sheath and ....etc

[:=Read Full Message Here=:]

....etc

[:=Read Full Message Here=:]

ABSTRACT

Low-k dielectrics are the very latest path breaking development in the field of Integrated Electronics. It is well on its way replacing the Al / SiO2 interconnects with the help of copper in CMOS fabrication of IC Chips. The CMOS technology has an in-built coupling capacitance which increases the time delay, thereby reducing associated processing speeds. This was compensated by reducing the thickness of the Al / SiO2 interconnects. There is a limit to the reduction in thickness after which an inverse effect is ....etc

[:=Read Full Message Here=:]

To get full information or details of dielectric resonator antenna please have a look on the pages

http://seminarsprojects.net/Thread-DIELECTRIC-RESONANT-ANTENNA

if you again feel trouble on dielectric resonator antenna please reply in that page and ask specific fields in dielectric resonator antenna ....etc

[:=Read Full Message Here=:]

Combined aerodynamic and electrostatic atomization of dielectric
liquid jets



Abstract

The electrical and atomization performance of a
plane plane charge injection atomizer using a dielectric
liquid, and operating at pump pressures ranging from 15 to
35 bar corresponding to injection velocities of up to 50 m/s,
is explored via low current electrical measurements, spray
imaging and phase Doppler anemometry. The work is
aimed at understanding the contribution of electrostatic
charging relevant to t ....etc

[:=Read Full Message Here=:]

Abstract
The need of low-loss substrate materials with stable dielectric performances over a wide frequency range is a strong
requirement when working at millimeter frequencies, where standard dielectric substrates exhibit prohibitive losses. In
this contribution, the authors focus their attention on a polymer material, the benzocyclobutene (BCB), having a low
dielectric constant equal to 2.65, and a low loss tangent, equal to 0.0008 at 1 GHz, with a stable dielectric behavior
over a broad frequency range, up to THz. The use of BCB ....etc

[:=Read Full Message Here=:]

Biasing a diode means applying appropriate DC voltage to a diode. A forward biased diode conducts
easily whereas reverse biased diode practically conducts no current. It means that forward resistance of a
diode is quite small as compared with its reverse resistance.
Forward current is the current flowing through a forward biased diode. Every diode has a maximum
value of forward current, which it can safely carry. If this value is exceeded, the diode may be destroyed
due to excessive heat. Reverse current or leakage current is the current t ....etc

[:=Read Full Message Here=:]