An EMI filter, or electromagnetic interference filter, is an electronic passive device that is used to suppress conductive interference that is present in a signal or an electrical line. EMI filters can be used to suppress interference that is generated by the device or other equipment to make a device more immune to electromagnetic interference signals present in the environment. Most EMI filters consist of components that suppress common and differential interference.

[ ....etc

[:=Read Full Message Here=:]

Abstract.
A novel Zero Voltage Transition (ZVT) technique based closed loop control of Boost Power Factor Correction (PFC) converter with Electro Magnetic Interference (EMI) Filter is presented in this paper. It operates at a xed frequency while achieving zero voltage turn-on of the main switch and zero current turn- off of the boost diode. This is accomplished by employing resonant operation only during switch transitions. During the rest of the cycle, the resonant network is essentially removed from the circuit and converter operation is id ....etc

[:=Read Full Message Here=:]

HIGH-DENSITY EMI FILTER DESIGN FOR DC-FED MOTOR DRIVES



INTRODUCTION

Electromagnetic interference (EMI) is one of the major design challenges in motor drive systems, especially in applications where stringent standards need to be followed. EMI noise is usually defined as common-mode (CM) and differential-mode (DM) noise. CM noise is defined as the noise flows between the power circuit and the ground, while DM noise is defined as the current following the same path as the power de ....etc

[:=Read Full Message Here=:]

difference between chopper fed drives and converter fed drives pdf

If the source of supply is d.c. (for example in a battery vehicle or a rapid transit system) a chopper-type converter is usually employed. The basic operation of a single-switch chopper was discussed in topic 2, where it was shown that the average output voltage could be varied by periodically switching the battery voltage on and of for varying intervals. The principal difference between the thyristor-controlled rectifier and the chopper is that in the former the motor current ....etc

[:=Read Full Message Here=:]

Am rema,want to know about an efficient common mode hybrid filter used in SMPS for my seminar work.

Abstract obtained from IEE is After the study of electromagnetic interference (EMI)
mechanisms in switching mode power system (SMPS) and the soft
switch, this paper proposes a novel hybrid filter (HEF) to suppress
commend mode EMI in SMPS. The HEF consists of a passive filter
and an active filter. Matching network, which can reduce
impedance mismatching effects, is introduced in passive part. A
feed-forward active filter is adopted ....etc

[:=Read Full Message Here=:]

Electromagnetic Interference (EMI) & Electromagnetic Compatibility (EMC)

INTRODUCTION

EMI-

It consists of any unwanted conducted or radiated signals of electric origin that can cause degradation in system or equipment performance.

EMC-

It is the ability of the system to function as designed without any degradation in performance due to EMI with in the operational environment

Classification of EMI

INTRASYSTEM EMI-

EMI problems with in the system one is dealing with.

INTERSYSTEM EMI-

EMI problems, that occur ....etc

[:=Read Full Message Here=:]

1. Passive and Active Hybrid Integrated EMI Filters
2. Active-Clamping Dual Resonant Converter
3. Implementation and Analysis of an Improved Series-Loaded Resonant DC-DC Converter Operating Above Resonance for Battery Chargers
4. Performance Analysis of PV Grid-connected Power Conditioning System with UPS
5. Positive Voltage Injection Switching Inductor (P-VISI) Method for Fast Transient Response in SMPS under Loading Condition
6. High-Voltage Auxiliary Power Supply Using Series-Connected MOSFETs and Floating Self-Driving Technique
7. Usi ....etc

[:=Read Full Message Here=:]

Presented By:
By Gordon A. Shaw, Jeremy S. Trethewey, A. David Johnson, Walter J. Drugan, and Wendy C. Crone

In this seminars, we examine the feasibility of using thin-film NiTi shape-memory alloys (SMAs) for thermomechanical data storage as an alternative to the polymer thin film used as the data storage medium in the IBM Millipede device.'8' NiTi is a potentially more robust and rapid storage medium than the polymer films currently used for thermomechanical data stor age. For example, the poly(methyl methacrylate) (PMMA) medium ....etc

[:=Read Full Message Here=:]

I am looking to attend an EMIEMC course in Apr. Wanted to see if I could find a course In Boston, Ma. on Apr 18, 19 and 20th ....etc

[:=Read Full Message Here=:]

CHAIN DRIVES IN LOW TORQUE DRIVES AND REDUCING PULSATIONS
INTRODUCTION TO DRIVES

Mechanical components used for power transmission. It may be belt, chain or gear depending on engine design parameters like - Distance between crankshaft and camshaft, engine maximum speed, engine-torque and engine construction cost. - Power transmission is done from one shaft to another shaft which may or may not rotate at same speed.

CHAIN DRIVES ....etc

[:=Read Full Message Here=:]