rigid axle suspension system ppt

A beam axle, rigid axle or solid axle is a dependent suspension design, in which a set of wheels is connected laterally by a single beam or shaft. Beam axles were once commonly used at the rear wheels of a vehicle, but historically they have also been used as front axles in rear-wheel-drive vehicles. In most automobiles, beam axles have been replaced by front and rear independent suspensions ....etc

[:=Read Full Message Here=:]

design of flexible and rigid pavement using lime cement and flyash as stabilizing materials ....etc

[:=Read Full Message Here=:]

FAST & AUTOMATIC METHOD FOR RIGID REGISTRATION OF MR IMAGES OF HUMAN BRAIN
SUBMITTED BY:
INDU LATA PREM
S7 AEI
College Of Engineering, Trivandrum
2007-11 batch


Hi friends, If you like this presentation, don't forget to thank the author [email protected]
OVERVIEW

INTRODUCTION
IMAGE REGISTRATION
CLASSIFICATION
APPROACHES
METHOD
EXPERIMENTAL RESULTS
ADVANTAGES
DISADVANTAGES
CONCLUSION

INTRODUCTION

Method for 3d registration.
Fast and automatic met ....etc

[:=Read Full Message Here=:]

To get information about flange coupling design refer the page link below

http://seminarsprojects.net/Thread-design-of-flange-coupling-ppt ....etc

[:=Read Full Message Here=:]

Asslam o Alikum Sir
I am the student of Bsc Civil Engineering and i need the information about th design of rigid and flexible pavements by using lime cement and flyash
Thanks
Regards
Rizwan Ali Rehan

Email Id: [email protected] ....etc

[:=Read Full Message Here=:]

design and fabrication of pneumatic auto feed drilling machiner eport

abstract

in small-scale industries and automobile maintenance shops, there are frequent needs of
tightening and loosening of screws, drilling, boring, grinding machine. huge and complicated
designed parts cannot be machined with the help of an ordinary machine and further for every
operation separate machine is required therefore increasing the number of machines required and
increasing the area required for them to be accommodated and hence overall initial cost req ....etc

[:=Read Full Message Here=:]

Design and size recommendations

The goal in designing the flange coupling is designed to optimize the number and size of bolts for flange couplings and flange dimensions. The number of bolts must be at least six.
Soles-supergrip bolt designed for maximum voltage shift of 280 n/mm2 and a maximum axial voltage of 350 n/mm2.
Design of torque
Design of torque shall be determined in accordance with
TD = TN S .. (1)
The shock factor may be selected from the table.
Number of soles-Supergrip bolts
Start by assuming the size of the bolt, then deter ....etc

[:=Read Full Message Here=:]

Abstract

Results of a 2-yr study of cause-effect relationships involved in roughness of concrete pavements are reported. Data were derived both from analog traces obtained with a profilograph in each wheelpath of randomly selected pavements within hours after placement, and from qualitative observations of placement methods. Construction sampled consisted of 184 sections of one - and - two - lane pavements built under 62 different contracts with seven different form-type finishing machines and three different slip-form pavers. Statistical anal ....etc

[:=Read Full Message Here=:]

Design and size recommendations

The goal in designing the flange coupling is designed to optimize the number and size of bolts for flange couplings and flange dimensions. The number of bolts must be at least six.
Soles-supergrip bolt designed for maximum voltage shift of 280 n/mm2 and a maximum axial voltage of 350 n/mm2.
Design of torque
Design of torque shall be determined in accordance with
TD = TN S .. (1)
The shock factor may be selected from the table.
Number of soles-Supergrip bolts
Start by assuming the size of the bolt, then deter ....etc

[:=Read Full Message Here=:]

IMPROVEMENT OF MECHANICAL PROPERTIES OF RIGID PAVEMENTS

INTRODUCTION
Transportation-basic infrastructure-development

Rigid and flexible

Basic neccesity-stable against loads

Rigid offers more strength load

But change in temp. warping up and warping down

To relieve stress-joint

Joint from the weaker plane and most of defects occur there

Increase the mechanical properties such as load carrying capacity and cracking resistance

Methods for improvement


Rigid Pavement
Consist of sub ....etc

[:=Read Full Message Here=:]