The HEF4543B is a BCD to 7-segment latch/decoder/driver for liquid crystal and LED displays. It has four address inputs (D0 to D3), an active LOW latch enable input (LE), an active HIGH blanking input (BL), an active HIGH phase input (PH) and seven buffered segment outputs (Qa to Qg). The circuit provides the function of a 4-bit storage latch and an 8-4-2-1 BCD to 7-segment decoder/driver. It can invert the logic levels of the output combination. The phase (PH), blanking (BL) and latch enable (LE) inputs are used to reverse the function table p ....etc

[:=Read Full Message Here=:]

please send me synopsis of fault analysis of electronic circuit using matlab bcd to 7 segment
please provide me synopsis of dis project..
....etc

[:=Read Full Message Here=:]

BCD binary numbers represent Decimal digits 0 to 9. A 4-bit BCD code is used torepresent the ten numbers 0 to 9. Since the 4-bit Code allows 16 possibilities, therefore thefirst 10 4-bit combinations are considered to be valid BCD combinations. The latter sixcombinations are invalid and do not occur.BCD Code has applications in Decimal Number display Systems such as Counters andDigital Clocks. BCD Numbers can be added together using BCD Addition. BCD Addition issimilar to normal Binary Addition except for the case when sum of two BCD digits exc ....etc

[:=Read Full Message Here=:]

To get full information or details of verilog program for reversible bcd adder please have a look on the pages

http://seminarsprojects.net/Thread-design-and-optimization-of-reversible-bcd-adder-subtractor-circuit-for-quantum-and-na

if you again feel trouble on verilog program for reversible bcd adder please reply in that page and ask specific fields in verilog program for reversible bcd adder ....etc

[:=Read Full Message Here=:]

An electricity meter, electric meter, electrical meter, or energy meter is a device that measures the amount of electric energy consumed by a residence, a business, or an electrically powered device.Electric utilities use electric meters installed at customers' premises to measure electric energy delivered to their customers for billing purposes. They are typically calibrated in billing units, the most common one being the kilowatt hour . They are usually read once each billing period.When energy savings during certain periods are desired, ....etc

[:=Read Full Message Here=:]

Hi.. I am doing the project on A new reversible design of BCD adders I need full report with simulation code(VERILOG or VHDL)..I have to submit within two days..so.pleas send me by tomorrow itself..My Email id is [email protected]. ....etc

[:=Read Full Message Here=:]

to construct adder subtractor using ic 7483 and to perform 4 bit adder subtractor

Introduction

To be able to perform arithmetic, you must first be familiar with numbers. Therefore, although we give a few helping examples, this article is not about binary numerals.

The main interactive circuit at the top of this page is an arithmetic circuit capable of performing both addition and subtraction on any two 4-bit binary numbers. The circuit has a Mode switch that allows you to choose between adding (M=0) and subtracting (M=1). To understand why t ....etc

[:=Read Full Message Here=:]

Where do i find an orcad library with any common Anode or common Cathode 7-segment display? ....etc

[:=Read Full Message Here=:]

To get full information or details of bcd subtractor using ic 7483 please have a look on the pages

http://seminarsprojects.net/Thread-design-and-optimization-of-reversible-bcd-adder-subtractor-circuit-for-quantum-and-na

if you again feel trouble on bcd subtractor using ic 7483 please reply in that page and ask specific fields in bcd subtractor using ic 7483 ....etc

[:=Read Full Message Here=:]

sir/madam,
may i know the information about the future scope of reversible bcd adder

mona ....etc

[:=Read Full Message Here=:]