MAIN PURPOSE:

The hydraulic jack is a device, which is used to lift heavy loads by applying a lot of small force. It is based on the PASCAL LAW, which states that the pressure intensity is equally transmitted in all directions through a mass of liquid in res

ITS PRINCIPLE OF MAIN OPERATION:

The operating principle of a hydraulic jack can be explained with the aid of the figure, some different parts are considered as a plunger and piston, operating on two cylinders of different diameter, which are interconnected at the b ....etc

[:=Read Full Message Here=:]

Analysis and Fabrication of Remote Control Lifting Jack

With the increasing levels of technology, the efforts being put to produce any kind of work has
been continuously decreasing. The efforts required in achieving the desired output can be
effectively and economically be decreased by the implementation of better designs.
Power screws are used to convert rotary motion into translatory motion. A screw jack is an
example of a power screw in which a small force applied in a horizontal plane is used to raise or
lower a large load. The prin ....etc

[:=Read Full Message Here=:]

To get full information or details of DESIGN AND FABRICATION OF HYDRAULIC JACK please have a look on the pages

http://seminarsprojects.net/Thread-remote-controlled-electrically-operated-hydraulic-jack

http://seminarsprojects.net/Thread-automatic-electro-hydraulic-jack-for-four-wheeler

if you again feel trouble on DESIGN AND FABRICATION OF HYDRAULIC JACK please reply in that page and ask specific fields in DESIGN AND FABRICATION OF HYDRAULIC JACK ....etc

[:=Read Full Message Here=:]

mini hydraulic press ppt

A hydraulic press is a device (see machine press) using a hydraulic cylinder to generate a compressive force. It uses the hydraulic equivalent of a mechanical lever, and was also known as a Bramah press after the inventor, Joseph Bramah, of England.He invented and was issued a patent on this press in 1795. As Bramah (who is also known for his development of the flush toilet) installed toilets, he studied the existing literature on the motion of fluids and put this knowledge into the development of the press.

Since the ....etc

[:=Read Full Message Here=:]

we want to know more about inbuilt hydraulic jack and its expense for preparation and how to build and where we get its components..etc..we dont give you any cash for service..i want only if it is free service.. ....etc

[:=Read Full Message Here=:]

abstract for mini hydraulic press

Small Hydraulic Press
We offer to our clients an advanced range of Small Hydraulic Press Up to 20 Ton. These have got to feature 200 mm stroke. Holding a vast capacity of up to 20 tons, these presses are compact in size. Further, these feature a fabricated stand, four pillar two guide bar and a dual pump and are thus, offered at market leading prices.
A hydraulic press is a machine press which uses hydraulic cylinder to generate a compressive force. The hydraulic press depends upon the Pascal's principle which ....etc

[:=Read Full Message Here=:]

To get full information or details of design and fabrication of mini hydraulic jack press please have a look on the pages

http://seminarsprojects.net/Thread-fabrication-of-hydraulic-jack-miniproject-abstract

http://seminarsprojects.net/Thread-design-development-and-fabrication-of-hydraulic-escalator-full-report

http://seminarsprojects.net/Thread-design-and-fabrication-of-gearbox-full-report

if you again feel trouble on design and fabrication of mini hydraulic jack press please reply in that page and ask specific fields in design and fabri ....etc

[:=Read Full Message Here=:]

sir i am pramod
i want to know about fabrication of multiuse hydraulic press.
i have adequate knowlege of press ....etc

[:=Read Full Message Here=:]

project report in hydraulic press design in pdf

ABSTRACT
In an attempt to alleviate the problem of the dearth of equipment in our laboratories in most of our higher institutions, a 30-ton hydraulic press was desgined, constructed and tested using locally sourced materials. The principal parameters of the design included the maximum load (300 kN), the distance the load resistance has to move (piston stroke, 150 mm), the system pressure, the cylinder area (piston diameter = 100 mm) and the volume flow rate of the working fluid. The major compone ....etc

[:=Read Full Message Here=:]

Cylinder Blind End Area (in square inches):

PI x (Cylinder Radius)2

Example: What is the area of a 6 diameter cylinder?

Diameter = 6
Radius is 1/2 of diameter = 3
Radius2 = 3 x 3 = 9

x (Cylinder Radius)2 = 3.14 x (3)2 = 3.14 x 9 = 28.26 square inches



Cylinder Rod End Area (in square inches):

Blind End Area - Rod Area

Example: What is the rod end area of a 6 diameter cylinder which has a 3 diameter rod?

Cylinder Blind End Area = 28.26 square inches
Rod Diameter = 3
Radius is 1/2 of rod diameter = 1.5
Radius2 = 1.5 x 1.5 ....etc

[:=Read Full Message Here=:]