Hi,
visit these threads for more details on this topic:
http://seminarsprojects.net/Thread-prototype-system-design-for-telemedicine-using-fixed-wireless-internet-downlaod-rep?pid=3424
http://seminarsprojects.net/Thread-prototype-system-design-for-telemedicine-using-fixed-wireless-internet ....etc

[:=Read Full Message Here=:]

A variable-speed controller, for an existing 225 kW fixed-speed wind power generator, is presented in this paper. A sensorless direct torque control algorithm-based controller is proposed for the squirrel-cage induction generator. Generator torque reference is derived based on sensorless maximum power tracking mode algorithm, up to the base speed of the generator. A three-phase front-end converter is used here to deliver the generated power to the grid with unity-power-factor operation at all wind speeds. This algorithm is based on direct activ ....etc

[:=Read Full Message Here=:]

1. INTRODUCTION
An electrodeless lamp is a light source in which the power required to generate light is transferred from the outside of the lamp envelope by means of (electro)magnetic fields, in contrast with a typical electrical lamp that uses electrical connections through the lamp envelope to transfer power. There are three advantages of eliminating electrodes:
Extended lamp life, because the electrodes are usually the limiting factor in lamp life.
The ability to use high efficiency light-generating substan ....etc

[:=Read Full Message Here=:]

details about in the power of the incandescent lamp used to illuminate
the LDR keeping all the lamp at a fixed distance ....etc

[:=Read Full Message Here=:]

This Project is very simple and when completed, causes a light-emitting diode (LED) to flash or pulse alternately on and off at a very slow rate, that is, at a low frequency. It could be used as a dummy car alarm indicator. You sometimes see these tiny pulsating lights in expensive cars protected by sophisticated car security systems, warning you that the car alarm is armed and ready.
For this design, the LED flashes on for a brief period and stays off for a relatively longer period. Because additional current is consumed from the battery ever ....etc

[:=Read Full Message Here=:]

this project is for designing a Fixed Timing call add in , and is a mobile project in which you can allow a user to restrict this out going call to certain time to utilize maximam benifit provided by mobile company at minimum cost.
As many mobile company profile different pulse rate for calls so many time user disconect the mobile before completing pulse rate or just entering another pulse when ever they can talk up to complete pulse for same cost.
so this project may be benificial for middle income group users,student .. by this applicati ....etc

[:=Read Full Message Here=:]

Performance Evaluation of Efficient and Reliable Routing Protocols for Fixed-Power Sensor Networks

ABSTRACT
A Fixed power wireless sensor networks are cost effective and prevalent, and they are facing lots of problems like RF interference, node failure from environmental noise and energy constraints. A routing protocol for Fixed power wireless sensor networks must overcome these problems. Because it have to achieve reliability, energy efficiency and scalability in message delivery. In this paper, we propose an efficient and ....etc

[:=Read Full Message Here=:]

To get full information or details of fixed assets management please have a look on the pages

http://seminarsprojects.net/Thread-fixed-asset-management-system-fams

if you again feel trouble on fixed assets management please reply in that page and ask specific fields in fixed assets management ....etc

[:=Read Full Message Here=:]

hello sir i want astract part on fixed assets management of kesoram cement would u post here please

hello sir i want five astract part on fixed assets management of kesoram cement would u post here please

....etc

[:=Read Full Message Here=:]

ABSTRACT

Shallow trench isolation (STI) requires a high quality oxide with superior fill capability provided by High Density Plasma (HDP) oxide. Unfortunately, the HDP deposition process can create large within die topographies that are difficult to polish directly using conventional silica slurries. As a result, etch back integration schemes have traditionally been incorporated for STI polish. A more revolutionary approach is the use of Fixed Abrasive (FA) CMP . FA CMP allows direct STI polish with good planarizatio ....etc

[:=Read Full Message Here=:]