ppt on manufacturing methods of knuckle joint

A knuckle joint is used to connect two rods which are under the action of tensile loads. However, if the joint is guided, the rods may support a compressive load. A knuckle joint may be readily disconnected for adjustments or repairs.

ABSTRACT
An improved method for manufacturing a steering knuckle and spindle unit for a heavy duty vehicle, such as a truck, including forming the spindle, separately forming the knuckle, and finally welding the knuckle and spindle together to form an integral unit. ....etc

[:=Read Full Message Here=:]

please provide me some necessary details about the calculation of slider crank mechanism ....etc

[:=Read Full Message Here=:]

SKYBUS METRO INTRODUCTION
The Skybus project was envisioned while looking at the pathetic roadcondition created by the metro infrastructure put in place on the wide roads whichhas caused enormous hardship and delays, traffic jams for the daily road users. Theconcept of metro as the solution to the city traffic jams as well as to handle large people movement from one area of the city to the other end seems very bright whenlooked upon from the surface level, whereas in reality people who owned the cars aswell as the public transport bus system o ....etc

[:=Read Full Message Here=:]

I need , 

U clamp and Saddle Support design calculations for Aboveground GRP pipeline

R ....etc

[:=Read Full Message Here=:]

yout ppts help for preaparing myself for seminar..collction of data was easily possible..it is one of the best ....etc

[:=Read Full Message Here=:]

The aim of the present paper is to study calculate the stresses in Knuckle joint using analytical method. Further study in this direction can made by using various directions of the pin and the capacity to withstand load. It is also to be noted that instead of mild steel pin we can also use high strength high modulus steel pin that can further enhance the capacity to withstand higher loads. The shape of the knuckle joint can be changed for improved properties. One can carry out the analysis by changing the shape in the part in the knuckle joint ....etc

[:=Read Full Message Here=:]

knuckle joint fmea

A knuckle joint is a mechanical joint used to connect two rods which are under a tensile load, when there is a requirement of small amount of flexibility, or angular moment is necessary. There is always axial or linear line of action of load. ....etc

[:=Read Full Message Here=:]

JOINT WRITTEN PROJECT PLAN AND DESIGN COMMENTS

8/29/2007
Manuel Santander
Mason Pokladnik


1. ASSIGNMENT
The project assignment was delivered by Stephen Northcutt on August 21:
Your topic will be perimeter convergence. In the past firewalls, VPN concentrators, IDS/IPS were hosted on separate devices. Today, Cisco ASA, IBM (formerly ISS) multithread appliance and others give you the same level of protection as individual systems. A recent paper from other students discusses this from a rapid respon ....etc

[:=Read Full Message Here=:]

knuckle joint design and calculations

Knuckle joints may be cast or fabricated or forged. In the knuckle joint illustrated, the rods are integral with the eye and fork (forged construction). However, the knuckle joint is often separate to the rods, and the rods need to be welded or screwed into the eye and fork. In the knuckle joint illustrated, there is no separate bearing and rotational or motion occurs between the pin and eye or pin and fork or both. If there is considerable movement, it may be necessary to use bearings to minimise fricti ....etc

[:=Read Full Message Here=:]

A knuckle joint is a mechanical joint used to connect two rods which are under a tensile load, when there is a requirement of small amount of flexibility, or angular moment is necessary. There is always axial or linear line of action of load.
Knuckle Joint
A knuckle joint is used to connect two rods which are under the action of tensile loads. However, if the joint is guided, the rods may support a compressive load. A knuckle joint may be readily disconnected for adjustments or repairs.
Its use may be found in the page link of a cycle chain, ....etc

[:=Read Full Message Here=:]