To get full information or details of relay distance please have a look on the pages

http://seminarsprojects.net/Thread-modeling-and-testing-of-a-digital-distance-relay-using-matlab-simulink

if you again feel trouble on relay distance please reply in that page and ask specific fields in relay distance ....etc

[:=Read Full Message Here=:]

to get information about the topic modelling and simulation of ecg RELATED TOPIC REFER THE LINK BELLOW

http://seminarsprojects.net/Thread-modelling-and-simulation-of-soft-switching ....etc

[:=Read Full Message Here=:]

The modeling and simulation of a grid-connected wind power system or WECS (acronym for Wind Energy Conversion System) has been carried out. Our goal is to design and test a power system of 14.9 KVA capacity, operating at 440V, 20m / s wind speed base, induction generator based on wind power system through. MATLAB simulation. The various components of a wind power system, namely wind turbine, generator, control system, rectifier-inverter, battery, load and other equipment, including transformers, network, etc., were Decided according to the scop ....etc

[:=Read Full Message Here=:]

MODELLING AND SIMULATION OF SOFT-SWITCHING DC/DC CONVERTER WITH HIGH VOLTAGE GAIN



INTRODUCTION

Recently, the demand for dc/dc converters with high
voltage gain has increased. The energy shortage and
atmosphere pollution have led to more researches on the
renewable and green energy sources such as the solar
arrays and the fuel cells. Moreover, the power systems
based on battery sources and super capacitors have been
increased. Unfortunately, the output voltages of these
sources are relativel ....etc

[:=Read Full Message Here=:]

to get information about the topic testing and modeling of digital distance relay using matlab related topic refer the page link bellow

http://seminarsprojects.net/Thread-modeling-and-testing-of-a-digital-distance-relay-using-matlab-simulink ....etc

[:=Read Full Message Here=:]

Presented By:
Marcin Janicki*, Marcin Daniel, Michal Szermer, Andrzej Napieralski

Abstract
The proper design and simulation of modern electronic microsystems oriented towards environment monitoring requires accurate models of various ambient sensors. In particular, this paper presents a comprehensive model of an ion sensitive eld effect transistor (ISFET). The model can be employed straightforwardly for simulations at device, circuit or system level. First, the model was validated with electrical measurements and simulatio ....etc

[:=Read Full Message Here=:]

Abstract
This paper describes modelling and testing of a
digital distance relay for transmission line protection using
MATLAB/SIMULINK. SIMULINK s Power System Blockset
(PSB) is used for detailed modelling of a power system
network and fault simulation. MATLAB is used to implement
programs of digital distance relaying algorithms and to serve
as main software environment. The technique is an
interactive simulation environment for relaying algorithm
design and evaluatio ....etc

[:=Read Full Message Here=:]

tiz website given a more idea to the research scholars..
it is a great website
....etc

[:=Read Full Message Here=:]

Abstract

A new concept in power generation is a microgrid. The Microgrid concept assumes a cluster of loads and microsources operating as a single controllable system that provides both power and heat to its local area. Not much is known about Microgrid behavior as a whole system. Some models exist which describe the components of a Microgrid. This thesis aims to model Microgrids at steady state and study their transient responses to changing inputs. Currently models of a Diesel Engine, a Fuel Cell, a Microturbine, a Wind turbine, and finally ....etc

[:=Read Full Message Here=:]

simulation model of upqc mdl file

The system can be applied to adjacent feeders to compensate for supply-voltage and load current imperfections on the main feeder and full compensation of supply-voltage imperfections on the other feeders. In the proposed configuration, all converters are connected back to back on the DC side and share a common DC-link capacitor. Therefore, power can be transferred from one feeder to adjacent feeders to compensate for sag/swell and interruption. The performance of the MC-UPQC as well as the adopted control algo ....etc

[:=Read Full Message Here=:]