i want this topic 'application of dc motor interfacing with 8051 microcontroller' please mail me on [email protected]

thank you. ....etc

[:=Read Full Message Here=:]

Suggest me source code for rotating a robot using GSM300 Module ,8051 microcontroller, max232ic ,motor driver . ....etc

[:=Read Full Message Here=:]

Dr.Y.NARASIMHA MURTHY Ph.D [email protected] Sensors and Interfacing techniquesIntroductionSensors are sophisticated devices which will detect and measure any non-electrical physicalquantity .A Sensor converts the physical parameter (for example: temperature, blood pressure,humidity, speed, etc.) into a signal which can be measured electrically.Sensor is sometimes called a primary measuring element, which can be found simply as amercury thermometer to measure the temperature. It may be embedded in the transducer toperform its function. That m ....etc

[:=Read Full Message Here=:]

sir/madam,
i am doing project on IPR 9600 and 8051,I don't no how to inerface and code.so please send information about that. ....etc

[:=Read Full Message Here=:]

its goodre you looking for lcd interfacing with 8051 microcontroller pdf ?
Type your request / requirement / comment about lcd interfacing with 8051 microcontroller pdf in to the right box for getting free material and support from us/dedicated premium ....etc

[:=Read Full Message Here=:]

soil moisture sensors interfacing with arm7 lpc2148

Soil moisture sensor

Soil moisture sensors measure the water content in soil. A soil moisture probe is made up of multiple soil moisture sensors.

This Soil Moisture Sensor can be used to detect the moisture of soil or judge if there is water around the sensor, let the plants in your garden reach out for human help.Insert this module into the soil and then adjust the on-board potentiometer to adjust the sensitivity. The sensor would outputs logic HIGH/LOW when the moisture is higher/lower th ....etc

[:=Read Full Message Here=:]

hello sir,
iam doing an project on pir sensor to turn on automatically light,for this purpose can u please help me out interfacing pir sensor with 8051 and its embeeded c code ....etc

[:=Read Full Message Here=:]

This is a simple-to-use liquefied petroleum gas (LPG) sensor, suitable for sensing LPG concentrations in the air. The MQ-6 can detect gas concentrations anywhere from 200 to 10000ppm.

This sensor has a high sensitivity and fast response time. The sensor's output is an analog resistance. The drive circuit is very simple; all you need to do is power the heater coil with 5V, add a load resistance, and connect the output to an ADC.

This sensor comes in a package similar to our MQ-3 alcohol sensor, and can be used with the breakout board .This c ....etc

[:=Read Full Message Here=:]

I am designing an AM receiver with these components, active antenna,RF amplifier, BP filter ADC,Microprocessor(8051), DAC, audio amplifier and a speaker. the DSP part is really challenging me.I am aiming at using FIR filter, a program to processed by 8051 being interfaced by adc and dac! Any help is highly welcome! ....etc

[:=Read Full Message Here=:]

//LCD Module Connections
sbit RS = P0^0;
sbit EN = P0^1;
sbit D0 = P2^0;
sbit D1 = P2^1;
sbit D2 = P2^2;
sbit D3 = P2^3;
sbit D4 = P2^4;
sbit D5 = P2^5;
sbit D6 = P2^6;
sbit D7 = P2^7;
//End LCD Module Connections

//Keypad Connections
sbit R1 = P1^0;
sbit R2 = P1^1;
sbit R3 = P1^2;
sbit R4 = P1^3;
sbit C1 = P1^4;
sbit C2 = P1^5;
sbit C3 = P1^6;
sbit C4 = P1^7;
//End Keypad Connections

void Delay(int a)
{
int j;
int i;
for(i=0;i {
for(j=0;j<100;j++)
{
}
}
}

char Read_Keypad()
{
C1 ....etc

[:=Read Full Message Here=:]