my respected coordinators,my name is amit navneet swain, i am from bhubaneswar,orissa and i am doing btech in GITA,bbsr. i want to know that why this class d amplifier is introduced to electronics?i mean what were the difficulties with the class ab amplifier?kindly explain me the reason..i expect i would get the best response from u.. ....etc

[:=Read Full Message Here=:]

Although the use of parametric amplifiers for high frequency, low noise amplification is relatively recent, the principles themselves are not at all new. They were first propounded by Lord Reyleigh in the 1880s for Mechanical Systems and by R. Hartley in 1930s for electrical applications. The need for extremely low noise amplification , as in radio telescopes, space probe tracking and communications, and tropospheric scatter receivers, spurred the design of useful parametric amplifiers in the late 1950s. The low ....etc

[:=Read Full Message Here=:]

please send me magnetic amplifiere ppt and documentation to [email protected] ....etc

[:=Read Full Message Here=:]

Characteristics of Operational Amplifiers

In analog computers and similar circuits, we make the assumption that the key component of the circuit the operational amplifier is perfect and ideal, with an infinite voltage gain and zero input current. Unfortunately, this is not possible in real-world devices. The questions we need to answer, then, are: how close can we come to the ideal, and how much error will be introduced into the results?
__
A very typical commercial IC op amp circuit is the 741. This IC has ....etc

[:=Read Full Message Here=:]

Presented by:
Ratish J. Punnoose

Introduction

Ex: An ultrasonic signal at 200kHz and another one at 201kHz will generate a 1kHz tone and a 401kHz signal which is inaudible to the human ear.

If an AM signal with a non-zero carrier amplitude is passed through Air, it is self-demodulated

- for more details on the topic and ppt, please follow the page link given below

http://ece.cmu.edu/ ece796/seminars/12/seminars/blacksonic.ppt ....etc

[:=Read Full Message Here=:]

feedback amplifiers pdf and ppt i want it completely hand written and alsoo very shor and descriptive ....etc

[:=Read Full Message Here=:]

A magnetic amplifier is a device which controls the power delivered from an a.c. source by employing a controllable non linear reactive elements or circuit generally interposed in series with the load. The power required to control the reactive element or circuit is made for less than the amount of power controlled; and hence power amplification is achieved. The non-linear reactive element is a saturable reactor. When used in a combination with a set of high-grade rectifiers, it exhibits power amplification properties in the sense that small ch ....etc

[:=Read Full Message Here=:]

Common mode rejection ratio (CMRR) is important performance parameter of any difference amplifier. It is the ratio of the differential gain to the common-mode gain, generally expressed in dB. It signifies the ability of an opamp to reject common mode signal, the signal which appears simultaneously at both its input terminals. The CMRR is of great importance when it comes to noise rejection. For applications involving high CMRR, instrumentation amplifiers consisting of three opamps are generally used. It has a major disadvantage that the value o ....etc

[:=Read Full Message Here=:]

Lin Xiao,
Zhuo Chen,
Chen Feng
Liang Liu
Zai-Qiao Bai
Yang Wang
Li Qian
Yuying Zhang
Qunqing Li
Kaili Jiang
Shoushan Fan


Abstract

We found that very thin carbon nanotube films, once fed by sound frequency electric currents, could emit loud sounds. This phenomenon
could be attributed to a thermoacoustic effect. The ultra small heat capacity per unit area of carbon nanotube thin films leads to a wide
frequency response range and a high sound pressure level. On the basis of this finding, we made practical c ....etc

[:=Read Full Message Here=:]

Common Base Amplifiers
Uses the same stabilised bias scheme as CE configuration.
Uses the same stabilised bias scheme as CE configuration.
The base is grounded for a.c. signals using a large capacitor.
Signal input at the emitter (between the emitter and the common base)
Signal output at the collector (between the collector and the common base) ....etc

[:=Read Full Message Here=:]