qwertyuiopasdfghjklzxcvbnmqwertyuiopasdfghjkl
qwertyuiopasdfghjklzxcvbnmqwertyuiopasdfghjkl ....etc

[:=Read Full Message Here=:]

thanks for proceeding.please send me ppts of cnc turning programming
thanks for proceedings please send me ppts of cnc turning
thanks for proceeding.please send me ppts of cnc turning programming thanks for proceedings please send me ppts of cnc turning ....etc

[:=Read Full Message Here=:]

An automatic lathe is a lathe (usually a metalworking lathe) whose actions are controlled automatically. Although all electronically controlled (CNC) lathes are automatic, they are usually not called by that name, as explained under General nomenclature. The first kinds of automatic lathes were mechanically automated ones, from the 1870s until the advent of NC and CNC in the 1950s and 1960s. CNC has not yet entirely displaced mechanically automated machines. The latter type of machine tool is no longer being newly built, but many existing exa ....etc

[:=Read Full Message Here=:]

To get full information or details of multi spindle automatic lathe ppt please have a look on the pages

http://seminarsprojects.net/Thread-automatic-lathes?pid=27295&mode=threaded

if you again feel trouble on multi spindle automatic lathe ppt please reply in that page and ask specific fields in multi spindle automatic lathe ppt ....etc

[:=Read Full Message Here=:]

As its name implies, backgear is a gear mounted at the back of the headstock (although in practice it is often located in other positions) that allows the chuck to rotate slowly with greatly-increased turning power. For a novice the ability to run a workpiece slowly might seem unnecessary, but a large-diameter casting, fastened to the faceplate and run at 200 r.p.m. (around the bottom speed commonly found on a lathe without backgear) would have a linear speed at its outer edge beyond the turning capacity of a small lathe. By engaging backgear ....etc

[:=Read Full Message Here=:]

A machine-tool dynamometer is a multi-component dynamometer that is used to measure forces during the use of the machine tool. Empirical calculations of these forces can be cross-checked and verified experimentally using these machine tool dynamometers.

With advances in technology, machine-tool dynamometers are increasingly used for the accurate measurement of forces and for optimizing the machining process. These multi-component forces are measured as an individual component force in each co-ordinate, depending on the coordinate system used ....etc

[:=Read Full Message Here=:]

Image result for lathe tool dynamometer
Client can avail from us Lathe Tool Dynamometer (Two component). It is used to measure cutting forces on various machines like lathe, drill, milling machines.
A machine-tool dynamometer is a multi-component dynamometer that is used to measure forces during the use of the machine tool. Empirical calculations of these forces can be cross-checked and verified experimentally using these machine tool dynamometers.
With advances in technology, machine-tool dynamometers are increasingly used for the accurate ....etc

[:=Read Full Message Here=:]

Althogh both have many similarities still they have some differences. Some of them are :-

Turret lathe:-

1. Turret tool head is directly fitted on the saddle and both of them appear like one unit

2. Saddle is moved to provide feed to the tool.

3. It is difficult to move the saddle for feed.

4. As the saddle can be moved along the entire length of the bed, it is suitable for longer workpieces.

5. To index the turret tool head, a clamping lever is released and the turret is rotated manually.

6. Limit dogs are used to control ....etc

[:=Read Full Message Here=:]

hii
jhdfvhfv
erfbjkhbrtkjlgniuyb th45
' h7yhuihbryt67tgfr]
iy dugihki87678hr]
rtut78dsfcs5 unbf uihdf]
;bn m gfl [- ....etc

[:=Read Full Message Here=:]

KK SADFHGJHJKHFGDSDSFBNM MHNGBDSAADFGHJBKHG SADFGJVC GG SSW 334534534 5345345345345WESDFDSGDFFHDJJ HJH HHFHHFHHJFGJJFYT JJGHJJ GFJFGJGJJG GHH ....etc

[:=Read Full Message Here=:]