Please, help me get it for studies. I can get the appropriate parameter values if I know which of them are needed. Thanks. ....etc

[:=Read Full Message Here=:]

Hi,

This is Jayesh Mahicha from India, looking for thermal and mechanical design
solution of helical coil heat exchanger(compact heat exchanger ).

I kindly request you to provide me supportive documents and xls on above at below,

[email protected]

Thank you & Best Regards,
Jayesh Mahicha. ....etc

[:=Read Full Message Here=:]

1
Two Way Slab
Two-Way Slab Design Based on ACI 318-11 using Finite Element Method
2
Voided Biaxial Slab
Voided Two-Way Slab Design Based on ACI 318-11
3
Anchorage to Concrete
Base Plate and Group Anchors Design Based on ACI 318-11 & AISC 360-10
4
Anchorage to Pedestal
Anchorage to Pedestal Design Based on ACI 318-11 & AISC 360-10
5
Circular Column
Circular Column Design Based on ACI 318-11
6
Concrete Column
Concrete Column Design Based on ACI 318-11
7
Super Composite Column
Super Composite Column Design Based on AISC 360-10 ....etc

[:=Read Full Message Here=:]

All books on Foundation engineering and also on concrete structure design will provide
the philosophy of pile foundation design.

Nos. of piles needed will depend upon the total vertical load from column / pile capacity
Pile group of three,four ,five ,six or more can be adopted based on nos of piles required.
Any moment acting from column is also accounted (as it will effect the exterior piles most)
by addtional +ve reaction on one side and -ve reaction on other side piles due to moment

Minimum c/c spacing between piles shall be: ....etc

[:=Read Full Message Here=:]

To get full information or details of rectangular tank calculation xls please have a look on the pages

http://scribddoc/98169867/Rectangular-Tank-Sizing#scribd

if you again feel trouble on rectangular tank calculation xls please reply in that page and ask specific fields in rectangular tank calculation xls ....etc

[:=Read Full Message Here=:]

elevated rectangular water tank xls

Reinforced Concrete Water tank design is based on IS 3370: 2009 (Parts I IV). The design depends on the location of tanks, i.e. overhead, on ground or underground water tanks. The tanks can be made in different shapes usually circular and rectangular shapes are mostly used. The tanks can be made of RCC or even of steel. The overhead tanks are usually elevated from the roof top through column. In the other hand the underground tanks are rested on the foundation.

TYPES OF WATER TANK

Basing on the location o ....etc

[:=Read Full Message Here=:]

pl send dense phase & vacuum type conveying in xls

mail id [email protected]

thanks

vikas ....etc

[:=Read Full Message Here=:]

design of self supporting chimney pdf

Self-supporting steel chimneys: When the lateral forces (wind or seismic forces) are transmitted to the foundation by the cantilever action of the chimney, then the chimney is known as self-supporting chimney. The self-supporting chimney together with the foundation remains stable under all working conditions without any additional support. A self-supporting chimney is shown in Fig. The self-supporting chimneys are made upto 10 m diameter and from 50 m to 100m in height.



Guyed steel chimneys: In high s ....etc

[:=Read Full Message Here=:]

Abstract
Water tanks are used to store water and are designed as crack free structures, to eliminate any leakage. In this paper design of two types of circular water tank resting on ground is presented. Both reinforced concrete (RC) and prestressed concrete (PSC) alternatives are considered in the design and are compared considering the total cost of the tank. These water tank are subjected to the same type of capacity and dimensions. As an objective function with the properties of tank that are tank capacity, width &length etc.

A computer pro ....etc

[:=Read Full Message Here=:]

Most of the industrial steel chimneys are tall structures with circular cross-sections. Such slender, lightly damped structures are prone to wind-exited vibration. Geometry of a self supporting steel chimney plays an important role in its structural behaviour under lateral dynamic loading. This is because geometry is primarily responsible for the stiffness parameters of the chimney. However, basic dimensions of industrial self supporting steel chimney, such as height, diameter at exit, etc., are generally derived from the associated environmen ....etc

[:=Read Full Message Here=:]