hi,can you tell me about self compacted concrete connection,please?
such as modelling this connection in abaqus

thanks ....etc

[:=Read Full Message Here=:]

By Nitish A. Jadhav
Guide: Mr. S. G. Vaidya




What is Tyre ?

Definition :
It is a Rubber
covering placed round
a wheel to form a soft
contact with the road

Tyre Inflation :
It is very important to check
accurate tire pressure gauge
Checking Tyre

Tread:
Tread wear indicator bars
when the tyre is worn to the
point where any of them
become visibly flushed with the
adjacent tread ribs, it is time to
replace the tyre ....etc

[:=Read Full Message Here=:]

ABSTRACT

This project work titled automatic tyre inflation system deals with the difficulty in driving the vehicles with low and high tyre pressure.
The irregular and uneven tyre pressures causes difficulty in driving and even leads to the accidents. This can be implemented on the vehicles which have air braking system.
The project automatic tyre inflation system is concentrated in maintaining the tyre pressures and thereby reducing the driving difficulties. This is done by mechanical means and not by using any sensors and other ele ....etc

[:=Read Full Message Here=:]

Tyre Threading



One of the most important parts of an automobile is the wheel and tyre. The importance of wheels and tyres in the automobile is obvious. Without the engine the car may be towed, but even that is not possible without the wheels and tyres. The wheel along with the tyre has to take the vehicle load, provide a cushioning effect and cope with the steering control.

A tyre is a cushion provided with an automobile wheel. It consists of mainly the outer tyre and the inner tube. The air inside the tube carries the entire load an ....etc

[:=Read Full Message Here=:]

Coupling
A coupling is a device used to connect two shafts together at their ends for the purpose of transmitting power. Couplings do not normally allow disconnection of shafts during operation, however there are torque limiting couplings which can slip or disconnect when some torque limit is exceeded.
The primary purpose of couplings is to join two pieces of rotating equipment while permitting some degree of misalignment or end movement or both. By careful selection, installation and maintenance of couplings, substantial savings can be made ....etc

[:=Read Full Message Here=:]

PERISTALTIC SELF INFLATING TYRE SYSTEM



SYNOPSIS

This project LINE FOLLOWER VEHICLE is carried out in our college.
To get an exposure about the Pre final year mini project, the university has included in our curriculum this semester.
The design and manufacturing are one of the major parts of the Mechanical Engineering branch. Hence in this project we have designed and fabricated a line follower which helps in load carrying application.
We have got some knowledge about ....etc

[:=Read Full Message Here=:]

Abstract:
Automatic Automotive Air Refilling System is designed to cater to safety requirements during driving of automobiles when its wheel gets deflected owing to puncture of tube. Our automobile is under load conditions because the pressure of air in tyres is less than required due to which engine does not work properly. Automatic Automotive Air Refilling System design is aimed at not only to fill the air in the punctured tyres automatically but also maintain the pressure of air in the running automotive. It also avoids damages in ....etc

[:=Read Full Message Here=:]

download the ppt on design and fabrication of tyre coupling pdf

ABSTRACT

Mild steel or wrought iron shaft are available in lengths varying from 6 to 10 meters, so as to make them handy and easy to transport. More lengthy shafts cannot be manufactured in a correct form to be used for power transmission. In engineering practice shafts of large lengths are required to transmit the torque which can be obtained by joining two or more shafts in order to obtain the required length. The joining of shafts is done by device is called as coupling.Tyre c ....etc

[:=Read Full Message Here=:]

hello ,
i am student of mechanical engineering and i wants to know the how tyre is exactly made from which process it is being made..if u r having any images or videolink related to tyre construction then give it to me ..thank you ....etc

[:=Read Full Message Here=:]

SIT - the Self Inflating Tire system is an invention of CODA DEVELOPMENT, a company based in the Czech Republic. The patented SIT solution offers a breakthrough in the solution of tire pressure problems.The SIT system is based on highly reliable and proven peristaltic pump principles. Use the weight and movement of the vehicle to inflate the tire as needed, obtaining air from the outside atmosphere. The entire system consists of two components: a tube chamber that functions as a peristaltic pump for the tire and a pressure control device to con ....etc

[:=Read Full Message Here=:]