Cylinder Blind End Area (in square inches):

PI x (Cylinder Radius)2

Example: What is the area of a 6 diameter cylinder?

Diameter = 6
Radius is 1/2 of diameter = 3
Radius2 = 3 x 3 = 9

x (Cylinder Radius)2 = 3.14 x (3)2 = 3.14 x 9 = 28.26 square inches



Cylinder Rod End Area (in square inches):

Blind End Area - Rod Area

Example: What is the rod end area of a 6 diameter cylinder which has a 3 diameter rod?

Cylinder Blind End Area = 28.26 square inches
Rod Diameter = 3
Radius is 1/2 of rod diameter = 1.5
Radius2 = 1.5 x 1.5 ....etc

[:=Read Full Message Here=:]

MAIN PURPOSE:

The hydraulic jack is a device, which is used to lift heavy loads by applying a lot of small force. It is based on the PASCAL LAW, which states that the pressure intensity is equally transmitted in all directions through a mass of liquid in res

ITS PRINCIPLE OF MAIN OPERATION:

The operating principle of a hydraulic jack can be explained with the aid of the figure, some different parts are considered as a plunger and piston, operating on two cylinders of different diameter, which are interconnected at the b ....etc

[:=Read Full Message Here=:]

we want to know more about inbuilt hydraulic jack and its expense for preparation and how to build and where we get its components..etc..we dont give you any cash for service..i want only if it is free service.. ....etc

[:=Read Full Message Here=:]

design of hydraulic service jack project pdf

Every hydraulic jack has six main components:

1. A RESERVOIR to hold hydraulic fluid.

2. A PUMP that draws fluid from the resevoir on it's up, suction or intake stroke then creates pressure on it's down/power stroke pushing the fluid through a..

3. CHECK VALVE which after allowing fluid to pass from the resevoir to the pump now 'checks' off the return port to the resevoir and directs the pressurized fluid to the..

4. MAIN CYLINDER ....etc

[:=Read Full Message Here=:]

To get full information or details of design of hydraulic jack please have a look on the pages

http://seminarsprojects.net/Thread-A-Project-Report-On-DESIGN-OF-HYDRAULIC-JACK-ANALYSIS?pid=161956

if you again feel trouble on design of hydraulic jack please reply in that page and ask specific fields in design of hydraulic jack ....etc

[:=Read Full Message Here=:]

To get full information or details of hydraulic press design calculations formulas please have a look on the pages

http://seminarsprojects.net/Thread-design-procedure-for-hydraulic-jack-pdf-file

http://seminarsprojects.net/Thread-design-fabrication-of-hydraulic-crane

if you again feel trouble on hydraulic press design calculations formulas please reply in that page and ask specific fields in hydraulic press design calculations formulas ....etc

[:=Read Full Message Here=:]

ABSTRACT

The conventional method of using rope, ladder, scaffold and even mechanical scissors lift in getting to a height encounter a lot of limitation (time and energy consumption, comfortability, amount of load that can be carried etc), which hydraulic scissors lift is set out to achieve. In this project a mobile scissors lift has been designed that will be powered by hydraulic to a height of 3m carrying a maximum load of 300kg. the project has been tested and it work successfully.

INTRODUCTION

A scissor lift or mechanism is a dev ....etc

[:=Read Full Message Here=:]

To get full information or details of design procedure for hydraulic jack pdf file please have a look on the pages

http://seminarsprojects.net/Thread-ppt-presentation-hydraulic-jack

http://seminarsprojects.net/Thread-design-development-and-fabrication-of-hydraulic-escalator-full-report

http://seminarsprojects.net/Thread-design-and-fabrication-of-gearbox-full-report

if you again feel trouble on design procedure for hydraulic jack pdf file please reply in that page and ask specific fields in design procedure for hydraulic jack pdf file ....etc

[:=Read Full Message Here=:]

To get full information or details of DESIGN AND FABRICATION OF HYDRAULIC JACK please have a look on the pages

http://seminarsprojects.net/Thread-remote-controlled-electrically-operated-hydraulic-jack

http://seminarsprojects.net/Thread-automatic-electro-hydraulic-jack-for-four-wheeler

if you again feel trouble on DESIGN AND FABRICATION OF HYDRAULIC JACK please reply in that page and ask specific fields in DESIGN AND FABRICATION OF HYDRAULIC JACK ....etc

[:=Read Full Message Here=:]

To get full information or details of hydraulic jack design calculations please have a look on the pages

http://seminarsprojects.net/Thread-hydraulic-jack

if you again feel trouble on hydraulic jack design calculations please reply in that page and ask specific fields in hydraulic jack design calculations ....etc

[:=Read Full Message Here=:]