CHAIN DRIVES IN LOW TORQUE DRIVES AND REDUCING PULSATIONS
INTRODUCTION TO DRIVES

Mechanical components used for power transmission. It may be belt, chain or gear depending on engine design parameters like - Distance between crankshaft and camshaft, engine maximum speed, engine-torque and engine construction cost. - Power transmission is done from one shaft to another shaft which may or may not rotate at same speed.

CHAIN DRIVES ....etc

[:=Read Full Message Here=:]

Simona Coman1, V. Comnac1, Member IEE, Cr. Boldisor1, D.C. Dumitrache2
1Automation Department, Transilvania University of Brasov, 5 M.Viteazu Str.,
500174 Brasov, Romania, phone/fax: +40 0268 418836,
2 Department of Automatic Control, Technical University of Cluj-Napoca,
26-28 Gh. Baritiu Str., 400027 Cluj-Napoca, Romania



Abstract

The distributed control systems with communication
networks are used in many industrial applications. These systems
are often referred as Networked Control Syste ....etc

[:=Read Full Message Here=:]

I need some ppts regarding special electrical drives like about SRM, BLDC, Stepper motors, Synchronous reluctance motors.. Pls i need it quickly ....etc

[:=Read Full Message Here=:]

difference between chopper fed drives and converter fed drives pdf

If the source of supply is d.c. (for example in a battery vehicle or a rapid transit system) a chopper-type converter is usually employed. The basic operation of a single-switch chopper was discussed in topic 2, where it was shown that the average output voltage could be varied by periodically switching the battery voltage on and of for varying intervals. The principal difference between the thyristor-controlled rectifier and the chopper is that in the former the motor current ....etc

[:=Read Full Message Here=:]

Abstract
The assembly of machine tool spindles results in a degree of variability in the effective stiffness of the bearings. This may result in a poor machining performance if the bearing stiffnesses are below their specified design values. Alternatively, the life of the bearings may be reduced if the bearings stiffnesses are above the design values because of excessive preload. This paper describes a method of checking the spindle assembly by making vibration measurements. From these measurements it is possible to determine which bearings (i ....etc

[:=Read Full Message Here=:]

To get full information or details of power converters and ac electrical drives with linear neural networks please have a look on the pages

http://seminarsprojects.net/Thread-energy-efficient-electrical-drives

http://seminarsprojects.net/Thread-an-ultrahigh-speed-low-power-electrical-drive-system

if you again feel trouble on power converters and ac electrical drives with linear neural networks please reply in that page and ask specific fields ....etc

[:=Read Full Message Here=:]

Today s buzzword IT has revolutionized every aspects of our day today working lives. Automation of industries is one of its main contributions. Automation can be defined as technology concerned with the application mechanical, electronic and computer-based systems to operate and control production. . The main advantage of automation is increased labor productivity at reduced labor cost. The heart of machine tool is a CNC (Computerized Numerical Control) system, which coordinates with the displays, PLC, drives system, and feed back systems. T ....etc

[:=Read Full Message Here=:]

what is the cross section of chip in milling machine process?? ....etc

[:=Read Full Message Here=:]

To get full information or details of machining and machine tools a b chattopadhyay please have a look on the pages

http://seminarsprojects.net/Thread-machine-tool-vibration-noise-ppt

if you again feel trouble on machining and machine tools a b chattopadhyay please reply in that page and ask specific fields in machining and machine tools a b chattopadhyay ....etc

[:=Read Full Message Here=:]

Electrical Drives of Machine Tools
Introduction
The arrangement of the motor nearby the operative member and also the use of variable-speed electric motors make it possible to simplify mechanical transmissions as well as the construction of the machine.
This helps to improve machine-tool design and considerably reduce the physical force required to handle the machine.
Introduction
One or more electric motors driving the operative members of the machine tool make up the machine's essential components.
T ....etc

[:=Read Full Message Here=:]