Presented By:
H-L Lin1, T Chou2, and C-P Chou2
Department of Vehicle Engineering, Army Academy R.O.C
Abstract:
Many parameters affect the quality of the resistance spot welding (RSW) process. It is not easy to obtain optimal parameters of the RSW process in the automobile industry. Conventionally, the Taguchi method has been widely used in engineering; however, with this method the desired results can only be obtained with the use of very discrete control factors, thus leading to uncertainty about the real optimum. In the process t ....etc

[:=Read Full Message Here=:]

i want modelling and thermal analysis of diesel engine piston with catia and ansys pdf material ....etc

[:=Read Full Message Here=:]

Hi,
visit this thread for an abstract:
http://seminarsprojects.net/Thread-modelling-of-transformers-with-internal-incipient-faults--6385

for pdf, follow the page link in this thread:
http://seminarsprojects.net/Thread-modelling-of-transformers-with-internal-incipent-faults-full-report ....etc

[:=Read Full Message Here=:]

to get information about the topic modelling and simulation of ecg RELATED TOPIC REFER THE LINK BELLOW

http://seminarsprojects.net/Thread-modelling-and-simulation-of-soft-switching ....etc

[:=Read Full Message Here=:]

SELECTION OF THE CUPOLA FURNACE AND FABRICATION OF THE MODEL

Done by
Name of group members
CEASE JUNIOR
FIJO GEORGE
FOUZIYA C M
HAREESH MOHANAN
JESBIN JOSEPH
JIBIN JOSEPH
ABSTRACT
A cupola or cupola furnace is a melting device used in foundries that can be used to melt cast iron, ni-resist iron and some bronzes. The cupola can be made in almost any practical size. The size of the cupola is represented or taken on the basis of the melting capacity and the diameters and can range from 18inches to 13 feet ....etc

[:=Read Full Message Here=:]

to get information about the topic induction motor simulink modelling full report ppt and related topic refer the page link bellow

http://seminarsprojects.net/Thread-modelling-of-the-three-phase-induction-motor-using-simulink ....etc

[:=Read Full Message Here=:]

Presented By:
Marcin Janicki*, Marcin Daniel, Michal Szermer, Andrzej Napieralski

Abstract
The proper design and simulation of modern electronic microsystems oriented towards environment monitoring requires accurate models of various ambient sensors. In particular, this paper presents a comprehensive model of an ion sensitive eld effect transistor (ISFET). The model can be employed straightforwardly for simulations at device, circuit or system level. First, the model was validated with electrical measurements and simulatio ....etc

[:=Read Full Message Here=:]

The modeling and simulation of a grid-connected wind power system or WECS (acronym for Wind Energy Conversion System) has been carried out. Our goal is to design and test a power system of 14.9 KVA capacity, operating at 440V, 20m / s wind speed base, induction generator based on wind power system through. MATLAB simulation. The various components of a wind power system, namely wind turbine, generator, control system, rectifier-inverter, battery, load and other equipment, including transformers, network, etc., were Decided according to the scop ....etc

[:=Read Full Message Here=:]

MODELLING AND SIMULATION OF SOFT-SWITCHING DC/DC CONVERTER WITH HIGH VOLTAGE GAIN



INTRODUCTION

Recently, the demand for dc/dc converters with high
voltage gain has increased. The energy shortage and
atmosphere pollution have led to more researches on the
renewable and green energy sources such as the solar
arrays and the fuel cells. Moreover, the power systems
based on battery sources and super capacitors have been
increased. Unfortunately, the output voltages of these
sources are relativel ....etc

[:=Read Full Message Here=:]

Abstract

In paper the fundamental question about optimal interaction between the controlling stimuli generated by the active (powered) and the passive (unpowered) drives of the robotic systems have been studied. A mathematical statement of the problem has been proposed that is suitable to study this question for the semi-passively actuated n-degree-of-freedom robotic systems. The problem is formulated as an optimal control problem for n-degree-of-freedom mechanical system models a semi-passively actuated robot. We take into account the inter ....etc

[:=Read Full Message Here=:]