Abstract
The effect of microprocessor pipeline depth on performance is considered. It is found that pipeline depth is a tradeoff between various factors, including the degree of superscalar processing, fraction of pipeline hazards, the fabrication technology of the processor, and the processor workload. The degree of instruction level parallelism decreases the optimal pipeline depth, while the lack of pipeline stalls increases the optimal pipeline depth. As we increase pipeline depth, there is a competition between greater pipeline throughput ....etc

[:=Read Full Message Here=:]

Modern home with optimum energy conservation



ABSTRACT

Now a day s technology increasing rapidly recently it is affecting home needs also. To make normal home to modern home we are introducing some luxury facilities like we can operate any of the electronic devices like FAN LIGHT AC with our T.V remote. For this application we are using AT-mega8 Micro controller which is heart of this project. Fallowing to microcontroller we are also using relays to operate AC appliances.
The Block diagram of the system ....etc

[:=Read Full Message Here=:]

I WANT THIS PROJECT IN MICRO CONTROLLER IN HARDWARE BASED.. CAN U SEND THE ABSTRACT AND PPT.. ....etc

[:=Read Full Message Here=:]

1. DISTRIBUTION SYSTEM

1.1 General description of Distribution System:

Distribution system is that part of the electric power system which connects the high voltage transmission network to the low voltage consumer service point

In any distribution system the power is distributed to various uses through feeders, distributors and service mains. Feeders are conductors of large current carrying capacity which carry the current in bulk to the feeding points. Distributors are conductors from w ....etc

[:=Read Full Message Here=:]

Abstract
Solid state control of ac power using diodes, thyristors and triacs injects the harmonics into the ac mains. These injected harmonics cause low efficiency in the supply system, poor power factor and EMI problems. Active filters have been considered a potential candidate to reduce these problems. This paper deals with an active power-filter (APF) based on simple control with optimum selection of energy storage capacitor. A voltage source inverter with hysteresis current control is employed to form the APF, which uses minimum measured ....etc

[:=Read Full Message Here=:]

A complex method for the optimum VAR control of radial primary power distribution networks dealing with the proper selection and installation of shunt capacitors is developed here. The problem is examined both on an annual and a long-term basis.

First objective functions and relative algorithms, which determine the kind, the size, the minimum numbers the locations and the adjustments of the possibly installed standard capacitors are developed. Then all these are embodied in a complex software package, which examines all the technically acce ....etc

[:=Read Full Message Here=:]

Presented By:
santosh
anakapalle.


ABSTRACT
Solar panel converts the light energy from the sun into electrical energy. In ordinary solar panel systems, the solar panel is fixed in a particular direction. The solar panel delivers maximum energy only when it faces directly towards the sun. Since the sun is moving continuously, the solar panel cannot deliver maximum energy when the solar panel fixed at one direction.
The goal of the project is to control the solar panel continuously, according to the moveme ....etc

[:=Read Full Message Here=:]

OPTIMUM DESIGN OF AN ACOUSTIC ENCLOSURE FOR DIESEL GENERATOR
Project presentation on OPTIMUM DESIGN OF AN ACOUSTIC ENCLOSURE FOR DIESEL GENERATOR


What is an acoustic enclosure
An acoustic enclosure is a containerized vessel used for housing generators to :
Reduce noise levels.
Improve reliability and durability of generator sets (gensets).
Easy serviceability.
High uptime of genset.
Improved aesthetic of genset.
Better working conditions.


Acoustic enclosures
Problem statement
Opt ....etc

[:=Read Full Message Here=:]

Determination of Optimum Process Parameters during turning of AISI 304



Introduction and literature survey

In machining process, Surface finish is one of the most significant technical requirements of the customer. A reasonably good surface finish is desired to improve the tribological properties, fatigue strength, corrosion resistance and aesthetic appeal of the product. Nowadays, manufacturing industries specially concerned to dimensional accuracy and surface finish. In order to obtain optimal cutting pa ....etc

[:=Read Full Message Here=:]

YES this is very easy to get and all things are very easy to handle ....etc

[:=Read Full Message Here=:]