A knuckle joint is a mechanical joint used to connect two rods which are under a tensile load, when there is a requirement of small amount of flexibility, or angular moment is necessary. There is always axial or linear line of action of load.
Knuckle Joint
A knuckle joint is used to connect two rods which are under the action of tensile loads. However, if the joint is guided, the rods may support a compressive load. A knuckle joint may be readily disconnected for adjustments or repairs.
Its use may be found in the page link of a cycle chain, ....etc

[:=Read Full Message Here=:]

please provide me some necessary details about the calculation of slider crank mechanism ....etc

[:=Read Full Message Here=:]

To get full information or details of gearbox design calculations pdf please have a look on the pages

http://seminarsprojects.net/Thread-design-and-fabrication-of-gearbox-full-report

http://seminarsprojects.net/Thread-design-development-and-fabrication-of-hydraulic-escalator-full-report

http://seminarsprojects.net/Thread-design-and-fabrication-of-gearbox-full-report

if you again feel trouble on gearbox design calculations pdf please reply in that page and ask specific fields in gearbox design calculations pdf ....etc

[:=Read Full Message Here=:]

ABSTRACT

The conventional method of using rope, ladder, scaffold and even mechanical scissors lift in getting to a height encounter a lot of limitation (time and energy consumption, comfortability, amount of load that can be carried etc), which hydraulic scissors lift is set out to achieve. In this project a mobile scissors lift has been designed that will be powered by hydraulic to a height of 3m carrying a maximum load of 300kg. the project has been tested and it work successfully.

INTRODUCTION

A scissor lift or mechanism is a dev ....etc

[:=Read Full Message Here=:]

ppt on manufacturing methods of knuckle joint

A knuckle joint is used to connect two rods which are under the action of tensile loads. However, if the joint is guided, the rods may support a compressive load. A knuckle joint may be readily disconnected for adjustments or repairs.

ABSTRACT
An improved method for manufacturing a steering knuckle and spindle unit for a heavy duty vehicle, such as a truck, including forming the spindle, separately forming the knuckle, and finally welding the knuckle and spindle together to form an integral unit. ....etc

[:=Read Full Message Here=:]

yout ppts help for preaparing myself for seminar..collction of data was easily possible..it is one of the best ....etc

[:=Read Full Message Here=:]

The aim of the present paper is to study calculate the stresses in Knuckle joint using analytical method. Further study in this direction can made by using various directions of the pin and the capacity to withstand load. It is also to be noted that instead of mild steel pin we can also use high strength high modulus steel pin that can further enhance the capacity to withstand higher loads. The shape of the knuckle joint can be changed for improved properties. One can carry out the analysis by changing the shape in the part in the knuckle joint ....etc

[:=Read Full Message Here=:]

A dog clutch, if successfully implemented in an automatic transmission, provides better packaging and the potential for improved fuel economy. The technical requirements for this concept are examined through modeling and simulation. As a first step, a physics-based component level model is developed that provides an understanding of the basic contact and impact dynamics. The model is compared to a built-in AMESim block to establish confidence. This component level model is then integrated into a powertrain system model within the AMESim environ ....etc

[:=Read Full Message Here=:]

knuckle joint design and calculations

Knuckle joints may be cast or fabricated or forged. In the knuckle joint illustrated, the rods are integral with the eye and fork (forged construction). However, the knuckle joint is often separate to the rods, and the rods need to be welded or screwed into the eye and fork. In the knuckle joint illustrated, there is no separate bearing and rotational or motion occurs between the pin and eye or pin and fork or both. If there is considerable movement, it may be necessary to use bearings to minimise fricti ....etc

[:=Read Full Message Here=:]

knuckle joint fmea

A knuckle joint is a mechanical joint used to connect two rods which are under a tensile load, when there is a requirement of small amount of flexibility, or angular moment is necessary. There is always axial or linear line of action of load. ....etc

[:=Read Full Message Here=:]