Gary Morphy
VARI-FORM

ABSTRACT
The need for lighter, stronger, more rigid vehicle structures will increasingly require complex hydroformed structural tubes to increase strength, and decrease weight, cost and part count. This effort will increase the use of high strength, low alloy (HSLA) steel, in place of SAE 1006/1008 or 1010 steel. Traditional hydroforming techniques require the higher elongation of the latter materials. An alternative tube hydroforming process has been developed to successfully use these, an ....etc

[:=Read Full Message Here=:]

Strength based and Displacement Based Design method for steel



Abstract

Performance based seismic design evaluates how a building is likely to perform for given earthquake loads. Seismic performance of a structure is closely associated with its strength, stiffness and ductility. In the present study structural strength and ductility mainly considered for the performance level for a steel moment resisting frame structure. The structure is analyzed according to Indian seismic code provision elastically un ....etc

[:=Read Full Message Here=:]

ABSTRACT

This test method covers determination of the compressive strength of hydraulic cement mortars, using 2-in. or cube specimens.Test Method C 349 provides an alternative procedure for this determination (not to be used for acceptance tests). This test method covers the application of the test using either inch-pound or SI units. The values stated in either system shall be regarded separately as standard. Within the text, the SI units are shown in brackets. ....etc

[:=Read Full Message Here=:]

My name harpreet singh from patiala ,Punjab
I have equipment to check the compression of mild steel . please send me a experiment repot of compressive strength of mildsteel.
compressive strength of mild steel whole experiment with observation? ....etc

[:=Read Full Message Here=:]

Abstract

This paper presents an alternative approach to speech enhancement by using compressed sensing (CS). CS is a new sampling theory, which states that sparse signals can be reconstructed from far fewer measurements than the Nyquist sampling. As such, CS can be exploited to reconstruct only the sparse components (e.g., speech) from the mixture of sparse and non-sparse components (e.g., noise). This is possible because in a time-frequency representation, speech signal is sparse whilst most noise is non-sparse. Derivation shows that on avera ....etc

[:=Read Full Message Here=:]

Efficient Coverage Maintenance Based
On Probabilistic Distributed Detection


ABSTRACT:
A wireless sensor network (WSN) is a wireless network which was specially discovered to monitor physical or environmental conditions, such as temperature, sound, vibration, pressure, motion. It consists of spatially distributed autonomous sensors to detect the conditions. Now-a-days many wireless sensor networks face the critical challenge of keep maintain ....etc

[:=Read Full Message Here=:]

ENERGY MINIMISATION TECHNIQUE IN
WIRELESS SENSOR NETWORK USING
COMPRESSIVE SENSING.
THESIS PRELIMINARY REPORT

Submitted by
REJIRAM R
Third Semester,M.Tech
Applied Electronics and Instrumentation




CHAPTER 1
INTRODUCTION
Compressed sensing (CS) is a new method of signal and image measurement and
reconstruction that takes advantage of the fact that many signals observed have sparse
representation under some basis. CS is an emerging model based framework for
signal recovery at a rate significantly be ....etc

[:=Read Full Message Here=:]

To get full information or details of compressive strength of cement total procedure please have a look on the pages

http://seminarsprojects.net/Thread-standard-test-method-for-compressive-strength-of-hydraulic-cement-mortars?pid=25291&mode=threaded

if you again feel trouble on compressive strength of cement total procedure please reply in that page and ask specific fields ....etc

[:=Read Full Message Here=:]

Abstract :

The case study project is significant since mild steel is used in structure, case hardening, gears, free cutting steels, shafting, forging etc. Mild steel plates were tested for mechanical properties like hardness, tensile strength, yield point etc. Later on the plates were joined by submerged arc welding and the mechanical properties were estimated again. Also weld ability, harden ability, tensile test etc. were conducted for the same result. ....etc

[:=Read Full Message Here=:]

To get full information or details of allowable stress for mild steel is 2062 please have a look on the pages

http://tenders.hpcltenders/tender_prog/tenderfiles/4288/Tender/New%20folder/TECH%20SPEC.pdf

if you again feel trouble on allowable stress for mild steel is 2062 please reply in that page and ask specific fields in allowable stress for mild steel is 2062 ....etc

[:=Read Full Message Here=:]