Abstract:
Mass customization manufacturing (MCM) has been gaining recognition as an industrial revolution in the 21st century. This paper presents innovative approaches in realizing and exercising MCM in theoretical and practical applications. Strategies of generalized production line platform and modularization are explored to support dynamic reconfigurations of MCM. NIST s XML-based Shop Data information integration specification is utilized to derive a data driven reconfigurable MCM modeling methodology. A simulation model of a Boeing air ....etc

[:=Read Full Message Here=:]

manufacturing of cotter joint ppt

A cotter joint is used to connect rigidly two co-axial rods or bars which are subjected to axial tensile or compressive forces . It is a temporary fastening .

COTTER

A cotter is a flat wedge shaped piece of rectangular cross section and its width is tapered (either on one side or on both sides) from one end to another for an easy adjustment.

APPLICATIONS OF COTTER

1. Connection of the piston rod with the cross heads
2. Joining o ....etc

[:=Read Full Message Here=:]

To get full information or details of ppt on manufacturing process of 500 mw stator winding turbogenerator please have a look on the pages

http://seminarsprojects.net/Thread-ppt-on-manufacturing-process-of-500-mw-stator-winding-turbogenerator

if you again feel trouble on ppt on manufacturing process of 500 mw stator winding turbogenerator please reply in that page and ask specific fields in ppt on manufacturing process of 500 mw stator winding turbogenerator ....etc

[:=Read Full Message Here=:]

A hinge is a flat wedge-shaped steel piece of rectangular cross-section which is inserted through the rods at a high angle with respect to its axes. It is uniform in thickness, but narrows in width, usually on only one side. The taper is generally 1 in 30. When a special arrangement such as a set screw is provided to prevent the cotter from loosening, its taper may be as large as 1 in 7. The end of the cotter is narrow Facilitate hammering for fastening and disassembly. The key-joints are generally used to rigidly fix two rods that are subjecte ....etc

[:=Read Full Message Here=:]

ppt on manufacturing methods of knuckle joint

A knuckle joint is used to connect two rods which are under the action of tensile loads. However, if the joint is guided, the rods may support a compressive load. A knuckle joint may be readily disconnected for adjustments or repairs.

ABSTRACT
An improved method for manufacturing a steering knuckle and spindle unit for a heavy duty vehicle, such as a truck, including forming the spindle, separately forming the knuckle, and finally welding the knuckle and spindle together to form an integral unit. ....etc

[:=Read Full Message Here=:]

manufacturing process of maggi noodles detail

Introduction:

Cereals like wheat , rice, maize and millets are staple food grain for majority of population around the world . These are the rich source of
carbohydrates and supply of calorie and other nutrients to the consumers. Apart from value addition by processing to traditional products from these grains , development of Newer products offers Variety, Convenience, Quality, Cost efficiency and Scope for increasing nutritional value.
In the developed countries many convenience foods are prepar ....etc

[:=Read Full Message Here=:]

To get full information or details of paint manufacturing process please have a look on the pages

http://seminarsprojects.net/Thread-manufacturing-process-management

if you again feel trouble on paint manufacturing process please reply in that page and ask specific fields in paint manufacturing process ....etc

[:=Read Full Message Here=:]

To get full information or details of sugar manufacturing process please have a look on the pages

sugar manufacturing processeminarprojectst-manufacturing-process-of-sugar-industry-and-utilization-of-by-products-of-sugar-indus

http://seminarsprojects.net/Thread-indian-sugar-industry

http://seminarsprojects.net/Thread-manufacturing-process-of-sugar-industry-and-utilization-of-by-products-of-sugar-indus

if you again feel trouble on sugar manufacturing process please reply in that page and ask specific fields in sugar manufacturing process ....etc

[:=Read Full Message Here=:]

ppt on selection of manufacturing method of cotter joint

COTTER JOINT

A cotter joint is used to connect rigidly two co-axial rods or bars which are subjected to axial tensile or compressive forces . It is a temporary fastening .A cotter joint is used to connect rigidly two co-axial rods or bars which are subjected to axial tensile or compressive forces. Here shaft is locked in place by a smaller pin that passes through the side of the lug and partly or completely through the shaft itself. This locking pin is named as cotter.
COTTER

A cotte ....etc

[:=Read Full Message Here=:]

A knuckle joint is a mechanical joint used to connect two rods which are under a tensile load, when there is a requirement of small amount of flexibility, or angular moment is necessary. There is always axial or linear line of action of load.
Knuckle Joint
A knuckle joint is used to connect two rods which are under the action of tensile loads. However, if the joint is guided, the rods may support a compressive load. A knuckle joint may be readily disconnected for adjustments or repairs.
Its use may be found in the page link of a cycle chain, ....etc

[:=Read Full Message Here=:]