I am writing this for one of my friends, he would like to apply for a build permit in local panchayath office. Please send me a copy of latest building permit malayalam application rules at your earliest.
thinking about to register.
M. Ashraf
[email protected] ....etc

[:=Read Full Message Here=:]

A hinge is a flat wedge-shaped steel piece of rectangular cross-section which is inserted through the rods at a high angle with respect to its axes. It is uniform in thickness, but narrows in width, usually on only one side. The taper is generally 1 in 30. When a special arrangement such as a set screw is provided to prevent the cotter from loosening, its taper may be as large as 1 in 7. The end of the cotter is narrow Facilitate hammering for fastening and disassembly. The key-joints are generally used to rigidly fix two rods that are subjecte ....etc

[:=Read Full Message Here=:]

The aim of the present paper is to study calculate the stresses in Knuckle joint using analytical method. Further study in this direction can made by using various directions of the pin and the capacity to withstand load. It is also to be noted that instead of mild steel pin we can also use high strength high modulus steel pin that can further enhance the capacity to withstand higher loads. The shape of the knuckle joint can be changed for improved properties. One can carry out the analysis by changing the shape in the part in the knuckle joint ....etc

[:=Read Full Message Here=:]

A knuckle joint is a mechanical joint used to connect two rods which are under a tensile load, when there is a requirement of small amount of flexibility, or angular moment is necessary. There is always axial or linear line of action of load.
Knuckle Joint
A knuckle joint is used to connect two rods which are under the action of tensile loads. However, if the joint is guided, the rods may support a compressive load. A knuckle joint may be readily disconnected for adjustments or repairs.
Its use may be found in the page link of a cycle chain, ....etc

[:=Read Full Message Here=:]

yout ppts help for preaparing myself for seminar..collction of data was easily possible..it is one of the best ....etc

[:=Read Full Message Here=:]

manufacturing of cotter joint ppt

A cotter joint is used to connect rigidly two co-axial rods or bars which are subjected to axial tensile or compressive forces . It is a temporary fastening .

COTTER

A cotter is a flat wedge shaped piece of rectangular cross section and its width is tapered (either on one side or on both sides) from one end to another for an easy adjustment.

APPLICATIONS OF COTTER

1. Connection of the piston rod with the cross heads
2. Joining o ....etc

[:=Read Full Message Here=:]

ppt on manufacturing methods of knuckle joint

A knuckle joint is used to connect two rods which are under the action of tensile loads. However, if the joint is guided, the rods may support a compressive load. A knuckle joint may be readily disconnected for adjustments or repairs.

ABSTRACT
An improved method for manufacturing a steering knuckle and spindle unit for a heavy duty vehicle, such as a truck, including forming the spindle, separately forming the knuckle, and finally welding the knuckle and spindle together to form an integral unit. ....etc

[:=Read Full Message Here=:]

knuckle joint design and calculations

Knuckle joints may be cast or fabricated or forged. In the knuckle joint illustrated, the rods are integral with the eye and fork (forged construction). However, the knuckle joint is often separate to the rods, and the rods need to be welded or screwed into the eye and fork. In the knuckle joint illustrated, there is no separate bearing and rotational or motion occurs between the pin and eye or pin and fork or both. If there is considerable movement, it may be necessary to use bearings to minimise fricti ....etc

[:=Read Full Message Here=:]

knuckle joint fmea

A knuckle joint is a mechanical joint used to connect two rods which are under a tensile load, when there is a requirement of small amount of flexibility, or angular moment is necessary. There is always axial or linear line of action of load. ....etc

[:=Read Full Message Here=:]

ppt on selection of manufacturing method of cotter joint

COTTER JOINT

A cotter joint is used to connect rigidly two co-axial rods or bars which are subjected to axial tensile or compressive forces . It is a temporary fastening .A cotter joint is used to connect rigidly two co-axial rods or bars which are subjected to axial tensile or compressive forces. Here shaft is locked in place by a smaller pin that passes through the side of the lug and partly or completely through the shaft itself. This locking pin is named as cotter.
COTTER

A cotte ....etc

[:=Read Full Message Here=:]