PROJECT GUIDE :
Dr.K.RAMANATHAN

Presented by:
K.KARTHIKEYAN




Abstract

Titanium nitride (TiN) is an extremely hard ceramic material, often used as a coating on titanium alloys, steel, carbide, and aluminium components to improve the substrate's surface properties.

Applied as a thin coating, TiN is used to harden and protect cutting and sliding surfaces, for decorative purposes (due to its gold appearance), and as a non-toxic exterior for medical implants.

TiN coating is for edge retention and corrosion r ....etc

[:=Read Full Message Here=:]

Integrating Structural Design and Formal Methods in RealTime System Design

Formal methods have been advocated as one of those techniques that can produce highquality software and hardware systems that has been demonstrated to come in ontime, within budget, and satisfy procurer requirements. They are, however, perceived to be difficult to use and unsuitable for presentation to nonspecialists. In addition, they have been criticized for paying too little attention to the system development process.

Traditional structur ....etc

[:=Read Full Message Here=:]

To get full information or details of psg design data book gear design please have a look on the pages

http://pvpsiddhartha.ac%5Csyllabus_2009%5Cmtech_ISEM_MD%5Cge.PDF

if you again feel trouble on psg design data book gear design please reply in that page and ask specific fields in psg design data book gear design ....etc

[:=Read Full Message Here=:]

ABSTRACT
The study of manufacturing was very important in order to carried out this project
to ensure that student understand on what are needs to do. This project is about designing
and fabricating the Recycle Bin Tin Can Crusher to helps people easy to crush the tin and
bring anywhere. This project involves the process of designing the crusher using
considering forces and ergonomic factor for people to use. After the design has complete,
it was transformed to its real product where the design is used for guide ....etc

[:=Read Full Message Here=:]

Submitted By
Vinit Tarey


ABSTRACT
Many system-on-chip (SoC) integrated circuits contain embedded cores with different scan frequencies. To better meet the test requirements for such heterogeneous SoCs, leading tester companies have recently introduced port-scalable testers, and Many IP core design software like Xilinx, Leonardo Spectrum, and Modelsim etc which can used to design ip core like DMA ,Interrupt Controller etc .These Ip core can be Power aware an Implement on soc by choosing different design tech ....etc

[:=Read Full Message Here=:]

Common Emitter BJT Amplifier Design Current Mirror Design


Some Random Observations
Conditions for stabilized voltage source biasing
Emitter resistance, RE, is needed.
Base voltage source will have finite resistance, RB.
needs to be much larger than RB.
Small RB - relative to RS - will attenuate input signal.
Larger RE permits larger RB, but results in lower gain.
Gain = -RC/RE for RE >> re.
Split RE with bypassing increases gain.
Requires large bypass cap ....etc

[:=Read Full Message Here=:]

to get information about the topic recycle bin tin can crusher full report refer the page link bellow

http://seminarsprojects.net/Thread-design-of-a-recycle-bin-tin-can-crusher?pid=51897&mode=threaded ....etc

[:=Read Full Message Here=:]

To get full information or details of electronic voting machine please have a look on the pages

http://seminarsprojects.net/Thread-electronic-voting-machine-project-full-report

if you again feel trouble on electronic voting machine please reply in that page and ask specific fields in electronic voting machine ....etc

[:=Read Full Message Here=:]

This article is presented by:
Sapana Mehta


Design Patterns

A pattern is a proven solution to a problem in a context.
Christopher Alexander says each pattern is a three-part rule which expresses a relation between a certain context, a problem, and a solution.
Design patterns represent a solutions to problems that arise when developing software within a particular context.
i.e Patterns = problems.solution pairs in a context

Background

Started in 1987 by Ward Cunningham and Ken Beck who were working w ....etc

[:=Read Full Message Here=:]

A feed passage 5 extends through one of the trunnions and suitable means such as screw conveyor 6 are provided for conveying the material to be ground through such passage and into the grinding chamber 7. A discharge passage 8 extends through the other trunnion and communicates with discharge spouts 9 and 10 for the ground material.bcone crusher spares for in South Africa A screen or perforated member 11 of suitable mesh may be provided for permitting only the iiner material to enter the discharge spout 19 hts.40min.any coarse material being di ....etc

[:=Read Full Message Here=:]