ppt on manufacturing methods of knuckle joint

A knuckle joint is used to connect two rods which are under the action of tensile loads. However, if the joint is guided, the rods may support a compressive load. A knuckle joint may be readily disconnected for adjustments or repairs.

ABSTRACT
An improved method for manufacturing a steering knuckle and spindle unit for a heavy duty vehicle, such as a truck, including forming the spindle, separately forming the knuckle, and finally welding the knuckle and spindle together to form an integral unit. ....etc

[:=Read Full Message Here=:]

PRESENTED BY,
Tauseef,
2nd MBA,A Sec,
SDM,Mangalore.

INTRODUCTION
Book referred Personnel Management and Industrial Relations by P.C.Tripathi.
Workers participation.
JMC meaning.
Features.
Functions.
Loopholes of JMC s.

WORKER S PARTICIPATION
There are two distinct groups of people in an undertaking:

Managers performing managerial functions. managers are held responsible for the work of their subordinates.

Workers performing operative functions. workers are ....etc

[:=Read Full Message Here=:]

manufacturing of cotter joint ppt

A cotter joint is used to connect rigidly two co-axial rods or bars which are subjected to axial tensile or compressive forces . It is a temporary fastening .

COTTER

A cotter is a flat wedge shaped piece of rectangular cross section and its width is tapered (either on one side or on both sides) from one end to another for an easy adjustment.

APPLICATIONS OF COTTER

1. Connection of the piston rod with the cross heads
2. Joining o ....etc

[:=Read Full Message Here=:]

Abstract:
Mass customization manufacturing (MCM) has been gaining recognition as an industrial revolution in the 21st century. This paper presents innovative approaches in realizing and exercising MCM in theoretical and practical applications. Strategies of generalized production line platform and modularization are explored to support dynamic reconfigurations of MCM. NIST s XML-based Shop Data information integration specification is utilized to derive a data driven reconfigurable MCM modeling methodology. A simulation model of a Boeing air ....etc

[:=Read Full Message Here=:]

A knuckle joint is a mechanical joint used to connect two rods which are under a tensile load, when there is a requirement of small amount of flexibility, or angular moment is necessary. There is always axial or linear line of action of load.
Knuckle Joint
A knuckle joint is used to connect two rods which are under the action of tensile loads. However, if the joint is guided, the rods may support a compressive load. A knuckle joint may be readily disconnected for adjustments or repairs.
Its use may be found in the page link of a cycle chain, ....etc

[:=Read Full Message Here=:]

Differentiate between sole proprietership ,partnership and joint stock company. ....etc

[:=Read Full Message Here=:]

why asa method is superior to zpf method ....etc

[:=Read Full Message Here=:]

ppt on selection of manufacturing method of cotter joint

COTTER JOINT

A cotter joint is used to connect rigidly two co-axial rods or bars which are subjected to axial tensile or compressive forces . It is a temporary fastening .A cotter joint is used to connect rigidly two co-axial rods or bars which are subjected to axial tensile or compressive forces. Here shaft is locked in place by a smaller pin that passes through the side of the lug and partly or completely through the shaft itself. This locking pin is named as cotter.
COTTER

A cotte ....etc

[:=Read Full Message Here=:]

ABSTRACT
A screw tube assembly is disclosed for use in a screw jack or the like. The screw tube assembly comprises a hollow tube member in one end of which is formed a recess so as to reduce the tube member wall thickness. Into this recess an annular bushing is inserted. A tip portion of the recessed tube wall is crimped over the received bushing outer end to lock the bushing in the tube against axial movement. A chordal portion of the bushing and overlying tube is then displaced radially outwardly to form an external tube assembly key and to ....etc

[:=Read Full Message Here=:]

A hinge is a flat wedge-shaped steel piece of rectangular cross-section which is inserted through the rods at a high angle with respect to its axes. It is uniform in thickness, but narrows in width, usually on only one side. The taper is generally 1 in 30. When a special arrangement such as a set screw is provided to prevent the cotter from loosening, its taper may be as large as 1 in 7. The end of the cotter is narrow Facilitate hammering for fastening and disassembly. The key-joints are generally used to rigidly fix two rods that are subjecte ....etc

[:=Read Full Message Here=:]