CHAIN DRIVES IN LOW TORQUE DRIVES AND REDUCING PULSATIONS
INTRODUCTION TO DRIVES

Mechanical components used for power transmission. It may be belt, chain or gear depending on engine design parameters like - Distance between crankshaft and camshaft, engine maximum speed, engine-torque and engine construction cost. - Power transmission is done from one shaft to another shaft which may or may not rotate at same speed.

CHAIN DRIVES ....etc

[:=Read Full Message Here=:]

I need this ppt. So please allow to download this..for that i shall be greatful to you..

sanjaya kumar sahu ....etc

[:=Read Full Message Here=:]

To get full information or details of z source inverter please have a look on the pages

http://seminarsprojects.net/Thread-z-source-inverter-for-motor-drives

if you again feel trouble on z source inverter please reply in that page and ask specific fields in z source inverter ....etc

[:=Read Full Message Here=:]

ADAPTIVE CONTROLLER FOR DC MOTOR DRIVES: A HARDWARE AND SOFTWARE APPROACH

F I Ahmed, A M El-Tobshy, A A Mahfouz, and M M Ibrahim
Faculty of Engineering, University of Cairo, Egypt



Abstract:

The most commonly used controller for the speed control of dc motor drives is (P-I) controller. In spite of the major features of the (P-I) controller, it has some disadvantages such as: the high starting overshoot in speed, the sensitivity to controller gains and the sluggish response due to sudden change ....etc

[:=Read Full Message Here=:]

difference between chopper fed drives and converter fed drives pdf

If the source of supply is d.c. (for example in a battery vehicle or a rapid transit system) a chopper-type converter is usually employed. The basic operation of a single-switch chopper was discussed in topic 2, where it was shown that the average output voltage could be varied by periodically switching the battery voltage on and of for varying intervals. The principal difference between the thyristor-controlled rectifier and the chopper is that in the former the motor current ....etc

[:=Read Full Message Here=:]

FLUX ESTIMATORS FOR SPEED-SENSORLESS
INDUCTION MOTOR DRIVES



Abstract

This thesis deals with flux estimators for speed-sensorless induction motor drives. To enhance
the stability and the performance of state-of-the-art sensorless drives, new flux estimator
designs based on the standard motor model are proposed. Theoretical and experimental
research methods are both used. The dynamics and stability of flux estimators
are analyzed using linearized models, and the effects of parameter errors are investig ....etc

[:=Read Full Message Here=:]

to get information about the topic z source inverter for adjustable speed drives a novel asd system related topic refer the page link bellow

http://seminarsprojects.net/Thread-z-source-inverter-for-motor-drives ....etc

[:=Read Full Message Here=:]

SPEED CONTROL OF SYNCHRONOUS MOTOR BY USING VARIABLE FREQUENCY DRIVES

ABSTRACT :

A novel open-loop speed control method for induction motors that provides high output torque and nearly zero steady-state speed error at any frequency is presented. The control scheme is based on the popular constant volts per hertz (V/f) method using low-cost open-loop current sensors. Only stator current measurements are needed to compensate for both stator resistance drop and slip frequency. The scheme proposed fully compensates for ....etc

[:=Read Full Message Here=:]

Abstract
This paper presents a Z-source inverter system and control for general-purpose motor drives. The Z-source inverter system employs a unique LC network in the dc page link and a small capacitor on the ac side of the diode front end. By controlling the shoot-through duty cycle, the Z-source can produce any desired output ac voltage, even greater than the line voltage. As a result, the new Z-source inverter system provides ride-through capability duringvoltage sags, reduces line harmonics, improves power factor and reliability, and ....etc

[:=Read Full Message Here=:]

Direct torque control (DTC) is one method used in variable frequency drives to control the torque (and thus finally the speed) of three-phase AC electric motors. This involves calculating an estimate of the motor's magnetic flux and torque based on the measured voltage and current of the motor. ....etc

[:=Read Full Message Here=:]