To get full information or details of hydraulic jack design calculations please have a look on the pages

http://seminarsprojects.net/Thread-hydraulic-jack

if you again feel trouble on hydraulic jack design calculations please reply in that page and ask specific fields in hydraulic jack design calculations ....etc

[:=Read Full Message Here=:]

rcc storage tank design for 1000 mt of material storage
material specific gravity is 1600 kg/m3 ....etc

[:=Read Full Message Here=:]

To get full information or details of hydraulic press design calculations formulas please have a look on the pages

http://seminarsprojects.net/Thread-design-procedure-for-hydraulic-jack-pdf-file

http://seminarsprojects.net/Thread-design-fabrication-of-hydraulic-crane

if you again feel trouble on hydraulic press design calculations formulas please reply in that page and ask specific fields in hydraulic press design calculations formulas ....etc

[:=Read Full Message Here=:]

To get full information or details of gearbox design calculations pdf please have a look on the pages

http://seminarsprojects.net/Thread-design-and-fabrication-of-gearbox-full-report

http://seminarsprojects.net/Thread-design-development-and-fabrication-of-hydraulic-escalator-full-report

http://seminarsprojects.net/Thread-design-and-fabrication-of-gearbox-full-report

if you again feel trouble on gearbox design calculations pdf please reply in that page and ask specific fields in gearbox design calculations pdf ....etc

[:=Read Full Message Here=:]

hi ,

My name is vivek gohel.i am 7th sem mechanical engineering student.i want seminar of design of automobile gearbox. and also tell me how many type of gear box are ?.and also send me automatic & munual gearbox seminars.

Thanking you,
v.r.gohel ....etc

[:=Read Full Message Here=:]

knuckle joint design and calculations

Knuckle joints may be cast or fabricated or forged. In the knuckle joint illustrated, the rods are integral with the eye and fork (forged construction). However, the knuckle joint is often separate to the rods, and the rods need to be welded or screwed into the eye and fork. In the knuckle joint illustrated, there is no separate bearing and rotational or motion occurs between the pin and eye or pin and fork or both. If there is considerable movement, it may be necessary to use bearings to minimise fricti ....etc

[:=Read Full Message Here=:]

ABSTRACT

The conventional method of using rope, ladder, scaffold and even mechanical scissors lift in getting to a height encounter a lot of limitation (time and energy consumption, comfortability, amount of load that can be carried etc), which hydraulic scissors lift is set out to achieve. In this project a mobile scissors lift has been designed that will be powered by hydraulic to a height of 3m carrying a maximum load of 300kg. the project has been tested and it work successfully.

INTRODUCTION

A scissor lift or mechanism is a dev ....etc

[:=Read Full Message Here=:]

SKYBUS METRO INTRODUCTION
The Skybus project was envisioned while looking at the pathetic roadcondition created by the metro infrastructure put in place on the wide roads whichhas caused enormous hardship and delays, traffic jams for the daily road users. Theconcept of metro as the solution to the city traffic jams as well as to handle large people movement from one area of the city to the other end seems very bright whenlooked upon from the surface level, whereas in reality people who owned the cars aswell as the public transport bus system o ....etc

[:=Read Full Message Here=:]

please provide me some necessary details about the calculation of slider crank mechanism ....etc

[:=Read Full Message Here=:]

A dog clutch, if successfully implemented in an automatic transmission, provides better packaging and the potential for improved fuel economy. The technical requirements for this concept are examined through modeling and simulation. As a first step, a physics-based component level model is developed that provides an understanding of the basic contact and impact dynamics. The model is compared to a built-in AMESim block to establish confidence. This component level model is then integrated into a powertrain system model within the AMESim environ ....etc

[:=Read Full Message Here=:]